CY7C68001-56PVXCT Cypress Semiconductor Corp, CY7C68001-56PVXCT Datasheet - Page 29
![CY7C68001-56PVXCT](/photos/6/50/65056/428-56-ssop_sml.jpg)
CY7C68001-56PVXCT
Manufacturer Part Number
CY7C68001-56PVXCT
Description
CY7C68001-56PVXCT
Manufacturer
Cypress Semiconductor Corp
Series
CY7Cr
Type
USBr
Datasheet
1.CY7C68001-56PVXC.pdf
(45 pages)
Specifications of CY7C68001-56PVXCT
Protocol
USB 2.0
Voltage - Supply
3 V ~ 3.6 V
Mounting Type
Surface Mount
Package / Case
56-SSOP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Number Of Drivers/receivers
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Table 13-10. Slave FIFO Synchronous Write Parameters with Externally Sourced IFCLK
Table 13-11. Slave FIFO Synchronous Packet End Strobe Parameters, Internally Sourced IFCLK
Table 13-12. Slave FIFO Synchronous Packet End Strobe Parameters, Externally Sourced IFCLK
There is no specific timing requirement that needs to be met for
asserting PKTEND pin with regards to asserting SLWR.
PKTEND can be asserted with the last data value clocked into
the FIFOs or thereafter. The only consideration is the setup time
t
Although there are no specific timing requirement for the
PKTEND assertion, there is a specific corner case condition that
needs attention while using the PKTEND to commit a one
byte/word packet. There is an additional timing requirement that
need to be met when the FIFO is configured to operate in auto
Document #: 38-08013 Rev. *J
t
t
t
t
t
t
t
t
t
t
t
t
t
t
SPE
IFCLK
SWR
WRH
SFD
FDH
XFLG
IFCLK
SPE
PEH
XFLG
IFCLK
SPE
PEH
XFLG
and the hold time t
Parameter
Parameter
Parameter
IFCLK Period
SLWR to Clock Setup Time
Clock to SLWR Hold Time
FIFO Data to Clock Setup Time
Clock to FIFO Data Hold Time
Clock to FLAGS Output Propagation Time
IFCLK Period
PKTEND to Clock Setup Time
Clock to PKTEND Hold Time
Clock to FLAGS Output Propagation Delay
IFCLK Period
PKTEND to Clock Setup Time
Clock to PKTEND Hold Time
Clock to FLAGS Output Propagation Delay
PEH
Figure 13-7. Slave FIFO Synchronous Packet End Strobe Timing Diagram
must be met.
PKTEND
FLAGS
IFCLK
Description
Description
Description
t
SPE
mode and it is desired to send two packets back to back: a full
packet (full defined as the number of bytes in the FIFO meeting
the level set in AUTOINLEN register) committed automatically
followed by a short one byte/word packet committed manually
using the PKTEND pin. In this particular scenario, user must
make sure to assert PKTEND at least one clock cycle after the
rising edge that caused the last byte/word to be clocked into the
previous auto committed packet.
is the value the AUTOINLEN register is set to when the IN
endpoint is configured to be in auto mode.
t
PEH
t
XFLG
20.83
12.1
14.6
Min
Min
Min
3.6
3.2
4.5
8.6
2.5
20
20
0
[14]
Max
13.5
Max
Max
13.5
200
9.5
Figure
[14]
[14]
[13]
shows this scenario. X
CY7C68001
Unit
Unit
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Page 29 of 45
[+] Feedback