CY7C1470V33-167BZI Cypress Semiconductor Corp, CY7C1470V33-167BZI Datasheet - Page 9
![IC,SYNC SRAM,2MX36,CMOS,BGA,165PIN,PLASTIC](/photos/6/76/67624/428-100-tqfp_14x20x1_4_sml.jpg)
CY7C1470V33-167BZI
Manufacturer Part Number
CY7C1470V33-167BZI
Description
IC,SYNC SRAM,2MX36,CMOS,BGA,165PIN,PLASTIC
Manufacturer
Cypress Semiconductor Corp
Datasheet
1.CY7C1470V33-200BZI.pdf
(33 pages)
Specifications of CY7C1470V33-167BZI
Format - Memory
RAM
Memory Type
SRAM - Synchronous
Memory Size
72M (2M x 36)
Speed
167MHz
Interface
Parallel
Voltage - Supply
3.135 V ~ 3.6 V
Operating Temperature
-40°C ~ 85°C
Package / Case
165-LFBGA
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
CY7C1470V33-167BZI
Manufacturer:
CYPRESS
Quantity:
11 698
Company:
Part Number:
CY7C1470V33-167BZI
Manufacturer:
Cypress Semiconductor Corp
Quantity:
10 000
Functional Overview
The CY7C1470V33, CY7C1472V33, and CY7C1474V33 are
synchronous-pipelined burst NoBL SRAMs designed specifically
to eliminate wait states during write/read transitions. All
synchronous inputs pass through input registers controlled by
the rising edge of the clock. The clock signal is qualified with the
clock enable input signal (CEN). If CEN is HIGH, the clock signal
is not recognized and all internal states are maintained. All
synchronous operations are qualified with CEN. All data outputs
pass through output registers controlled by the rising edge of the
clock. Maximum access delay from the clock rise (t
(250 MHz device).
Accesses can be initiated by asserting all three chip enables
(CE
enable (CEN) is active LOW and ADV/LD is asserted LOW, the
address presented to the device will be latched. The access can
either be a read or write operation, depending on the status of
the write enable (WE). BW
operations.
Write operations are qualified by the write enable (WE). All writes
are simplified with on-chip synchronous self timed write circuitry.
Three synchronous chip enables (CE
asynchronous output enable (OE) simplify depth expansion. All
operations (reads, writes, and deselects) are pipelined. ADV/LD
should be driven LOW after the device has been deselected in
order to load a new address for the next operation.
Single Read Accesses
A read access is initiated when the following conditions are
satisfied at clock rise: (1) CEN is asserted LOW, (2) CE
and CE
WE is deasserted HIGH, and (4) ADV/LD is asserted LOW. The
address presented to the address inputs is latched into the
address register and presented to the memory core and control
logic. The control logic determines that a read access is in
progress and allows the requested data to propagate to the input
of the output register. At the rising edge of the next clock the
requested data is allowed to propagate through the output
register and onto the data bus within 3.0 ns (250 MHz device)
Document Number: 38-05289 Rev. *M
TMS
TCK
V
V
V
NC
NC(144M,
288M,
576M, 1G)
ZZ
Pin Definitions
Pin Name
DD
DDQ
SS
1
, CE
3
are all asserted active, (3) the write enable input signal
2
, CE
Test mode select
synchronous
JTAG clock
Power supply
I/O power supply Power supply for the I/O circuitry.
Ground
–
–
Input-
asynchronous
3
) active at the rising edge of the clock. If clock
I/O Type
(continued)
[x]
can be used to conduct byte write
This pin controls the test access port state machine. Sampled on the rising edge of TCK.
Clock input to the JTAG circuitry.
Power supply inputs to the core of the device.
Ground for the device. Should be connected to ground of the system.
No connects. This pin is not connected to the die.
These pins are not connected. They will be used for expansion to the 144M, 288M, 576M, and
1G densities.
ZZ “Sleep” input. This active HIGH input places the device in a non-time critical “sleep” condition
with data integrity preserved. During normal operation, this pin has to be LOW or left floating.
ZZ pin has an internal pull-down.
1
, CE
2
, CE
CO
3
) is 3.0 ns
) and an
1
, CE
2
,
provided OE is active LOW. After the first clock of the read
access the output buffers are controlled by OE and the internal
control logic. OE must be driven LOW in order for the device to
drive out the requested data. During the second clock, a
subsequent operation (read/write/deselect) can be initiated.
Deselecting the device is also pipelined. Therefore, when the
SRAM is deselected at clock rise by one of the chip enable
signals, its output will tristate following the next clock rise.
Burst Read Accesses
The CY7C1470V33, CY7C1472V33, and CY7C1474V33 have
an on-chip burst counter that allows the user the ability to supply
a single address and conduct up to four reads without
reasserting the address inputs. ADV/LD must be driven LOW in
order to load a new address into the SRAM, as described in the
Single Read Accesses
counter is determined by the MODE input signal. A LOW input
on MODE selects a linear burst mode, a HIGH selects an
interleaved burst sequence. Both burst counters use A0 and A1
in the burst sequence, and will wrap-around when incremented
sufficiently. A HIGH input on ADV/LD will increment the internal
burst counter regardless of the state of chip enables inputs or
WE. WE is latched at the beginning of a burst cycle. Therefore,
the type of access (read or write) is maintained throughout the
burst sequence.
Single Write Accesses
Write accesses are initiated when the following conditions are
satisfied at clock rise: (1) CEN is asserted LOW, (2) CE
and CE
asserted LOW. The address presented to the address inputs is
loaded into the address register. The write signals are latched
into the control logic block.
On the subsequent clock rise the data lines are automatically
tristated regardless of the state of the OE input signal. This
allows the external logic to present the data on DQ and DQP
(DQ
DQ
CY7C1472V33). In addition, the address for the subsequent
access (read/write/deselect) is latched into the address register
(provided the appropriate control signals are asserted).
Pin Description
a,b,c,d
a,b,c,d,e,f,g,h
3
/DQP
are all asserted active, and (3) the write signal WE is
a,b,c,d
/DQP
a,b,c,d,e,f,g,h
for CY7C1470V33 and DQ
section above. The sequence of the burst
for
CY7C1470V33
CY7C1472V33
CY7C1474V33
CY7C1474V33,
a,b
Page 9 of 33
/DQP
1
, CE
a,b
for
2
[+] Feedback
,