CY7C09579V-100BBC Cypress Semiconductor Corp, CY7C09579V-100BBC Datasheet - Page 25
![IC,SYNC SRAM,32KX36,CMOS,BGA,172PIN,PLASTIC](/photos/28/21/282118/172-lfbga_sml.jpg)
CY7C09579V-100BBC
Manufacturer Part Number
CY7C09579V-100BBC
Description
IC,SYNC SRAM,32KX36,CMOS,BGA,172PIN,PLASTIC
Manufacturer
Cypress Semiconductor Corp
Datasheet
1.CY7C09579V-100AXC.pdf
(32 pages)
Specifications of CY7C09579V-100BBC
Format - Memory
RAM
Memory Type
SRAM - Dual Port, Synchronous
Memory Size
1.152M (32K x 36)
Speed
100MHz
Interface
Parallel
Voltage - Supply
3 V ~ 3.6 V
Operating Temperature
0°C ~ 70°C
Package / Case
172-LFBGA
Lead Free Status / RoHS Status
Contains lead / RoHS compliant by exemption
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
CY7C09579V-100BBC
Manufacturer:
CY
Quantity:
5 780
Company:
Part Number:
CY7C09579V-100BBC
Manufacturer:
Cypress Semiconductor Corp
Quantity:
10 000
Part Number:
CY7C09579V-100BBC
Manufacturer:
CYPRESS/赛普拉斯
Quantity:
20 000
Document Number: 38-06054 Rev. *E
Counter Operation
The CY7C09569V/09579V Dual-Port RAM (DPRAM) contains
on-chip address counters (one for each port) for the
synchronous members of the product family. Besides the main
x36 format, the right port allows bus matching (x18 or x9,
user-selectable). An internal sub-counter provides the extra
addresses required to sequence out the 36-bit word in 18-bit
or 9-bit increments. The sub-counter counts up in the “Little
Endian” mode, and counts down if the user has chosen the
“Big Endian” mode. The address counter is required to be in
increment mode in order for the sub-counter to sequence out
the second word (in x18 mode) or the remaining three bytes
(in x9 mode).
For a x36 format (the only active format on the left port), each
address counter in the CY7C09579V uses addresses (A
For the right port (allowing for the bus-matching feature), a
maximum of two address bits (out of a 2-bit sub-counter) are
added.
A new read-back (Hold+Read Mode) feature has been added,
which is different between the left and right port due to the bus
matching feature provided only for the right port. In read-back
mode the internal address of the counter will be read from the
data I/Os as shown in
Address
1. ADS
2. CNTEN
3. CNTRST
Note
CNTRST
82. Even though a logic level applied to a “Don’t Care” input will not change the logical operation of the dual-port, inputs that are temporarily a “Don’t Care” (along
______________
CNTEN
____________
loading of that port's burst counters if the corresponding
CNTEN
to stall the operation of the address input and utilize the
internal address generated by the internal counter for fast
interleaved memory applications; when asserted, the
address counter will increment on each positive transition
of that port's clock signal.
with unused inputs) must not be allowed to float. They must be forced either HIGH or LOW.
ADS
I/O’s
_______
L/R
Figure 1. Counter Operation Diagram
L/R
L/R
(pin #23/86) is a port’s address strobe, allowing the
L/R
pin is active as well.
(pin #25/84) is a port’s count enable, provided
(pin #24/85) is a port's burst counter reset.
Figure
1.
CY7C09569V
CY7C09579V
ARRAY
RAM
0–14
).
Bus Match Operation
The right port of the CY7C09569V/09579V 16K/32Kx36
dual-port SRAM can be configured in a 36-bit long-word, 18-bit
word, or 9-bit byte format for data I/O. The data lines are
divided into four lanes, each consisting of 9 bits (byte-size data
lines).
The Bus Match Select (BM) pin works with Bus Size Select
(SIZE) and Big Endian Select (BE) to select the bus width
(long-word, word, or byte) and data sequencing arrangement
for the right port of the dual-port device. A logic “0” applied to
both the Bus Match Select (BM) pin and to the Bus Size Select
(SIZE) pin will select long-word (36-bit) operation. A logic “1”
level applied to the Bus Match Select (BM) pin will enable
whether byte or word bus width operation on the right port I/Os
depending on the logic level applied to the SIZE pin. The level
of Bus Match Select (BM) must be static throughout normal
device operation.
The Bus Size Select (SIZE) pin selects either a byte or word
data arrangement on the right port when the Bus Match Select
(BM) pin is HIGH. A logic “1” on the SIZE pin when the BM pin
is HIGH selects a byte bus (9-bit) data arrangement. A logic
“0” on the SIZE pin when the BM pin is HIGH selects a word
bus (18-bit) data arrangement. The level of the Bus Size Select
(SIZE) must also be static throughout normal device operation.
The Big Endian Select (BE) pin is a multiple-function pin during
word or byte bus selection (BM = 1). BE is used in Big Endian
Select mode to determine the order by which bytes (or words)
of data are transferred through the right data port. A logic “0”
on the BE pin will select Little Endian data sequencing
arrangement and a logic “1” on the BE pin will select a Big
Endian data sequencing arrangement. Under these circum-
stances, the level on the BE pin should be static throughout
dual-port operation.
Long-Word (36-bit) Operation
Bus Match Select (BM) and Bus Size Select (SIZE) set to a
logic “0” will enable standard cycle long-word (36-bit)
operation. In this mode, the right port’s I/O operates essentially
in an identical fashion to the left port of the dual-port SRAM.
However no Byte Select control is available. All 36 bits of the
long-word are shifted into and out of the right port’s I/O buffer
stages. All read and write timing parameters may be identical
with respect to the two data ports. When the right port is
configured for a long-word size, Big- Endian Select (BE) pin
has no application and their inputs are “Don’t Care”
external user.
Figure 2. Bus Match Operation Diagram
x36
/
CY7C09569V
CY7C09579V
16K/32Kx36
Dual Port
9
/
9
/
9
/
9
/
BM SIZE
BE
CY7C09569V
CY7C09579V
x9, x18, x36
Page 25 of 32
/
[82]
for the
[+] Feedback