CS5530-ISZR Cirrus Logic Inc, CS5530-ISZR Datasheet - Page 28

• Manufacturer Part Number: CS5530-ISZR
• Description: IC 24-Bit 1-ch Low Noise ADC
• Manufacturer: Cirrus Logic Inc

Specifications of CS5530-ISZR

• Number Of Bits: 24
• Sampling Rate (per Second): 3.84k
• Data Interface: Serial
• Number Of Converters: 1
• Power Dissipation (max): 45mW
• Voltage Supply Source: Analog and Digital, Dual ±
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 20-SSOP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 598-1158 - BOARD EVAL FOR CS5530
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

2.9 Clock Generator
The CS5530 includes an on-chip inverting amplifi-
er which can be connected with an external crystal
to provide the master clock for the chip. Figure 17
illustrates the on-chip oscillator. It includes loading
capacitors and a feedback resistor to form a Pierce
oscillator configuration. The chips are designed to
operate using a 4.9152 MHz crystal; however, oth-
er crystals with frequencies between 1 MHz to 5
MHz can be used. One lead of the crystal should be
connected to OSC1 and the other to OSC2. Lead
lengths should be minimized to reduce stray capac-
itance. Note that while using the on-chip oscillator,
neither OSC1 or OSC2 is capable of directly driv-
ing any off chip logic. When the on-chip oscillator
is used, the voltage on OSC2 is typically 1/2 V
peak-to-peak. This signal is not compatible with
external logic unless additional external circuitry is
added. The OSC2 output should be used if the on-
chip oscillator output is used to drive other circuit-
ry.
The designer can use an external CMOS compati-
ble oscillator to drive OSC2 with a 1 MHz to 5
MHz clock for the ADC. The external clock into
OSC2 must overdrive the 60 microampere output
of the on-chip amplifier. This will not harm the on-
chip circuitry. In this scheme, OSC1 should be left
unconnected.
28
OSC1
NOTE: 20 pF capacitors are on chip and
should not be added externally.
Figure 17. On-chip Oscillator Model
20 pF
1 MΩ
~ ~ 60 μA
20 pF
V
OSC2
TH
+
-
MCLK
2.10 Power Supply Arrangements
The CS5530 is designed to operate from single or
dual analog supplies and a single digital supply.
The following power supply connections are possi-
ble:
VA+ = +5 V; VA- = 0 V; VD+ = +3 V to +5 V
VA+ = +2.5 V; VA- = -2.5 V; VD+ = +3 V to +5 V
VA+ = +3 V; VA- = -3 V; VD+ = +3 V
A VA+ supply of +2.5 V, +3.0 V, or +5.0 V should
be maintained at ±5% tolerance. A VA- supply of
-2.5 V or -3.0 V should be maintained at ±5% tol-
erance. VD+ can extend from +2.7 V to +5.5 V
with the additional restriction that [(VD+) - (VA-)
< 7.5 V].
Figure 18 illustrates the CS5530 connected with a
single +5.0 V supply to measure differential inputs
relative to a common mode of 2.5 V. Figure 19 il-
lustrates the CS5530 connected with ±2.5 V bipolar
analog supplies and a +3 V to +5 V digital supply
to measure ground referenced bipolar signals. Fig-
ures 20 illustrates the CS5532 connected with ±3 V
analog supplies and a +3 V digital supply to mea-
sure ground referenced bipolar signals.
CS5530
DS742F3