CS42516-CQZR Cirrus Logic Inc, CS42516-CQZR Datasheet - Page 27

• Manufacturer Part Number: CS42516-CQZR
• Description: IC,Soundcard Circuits,QFP,64PIN,PLASTIC
• Manufacturer: Cirrus Logic Inc

DS583F1
4.6
4.6.1
OMCK/LRCK Ratio
SCLK/LRCK Ratio
Digital Interfaces
When either serial port is in Slave Mode, its respective LRCK signal must be present for proper device
operation.
In Slave Mode, One-Line Mode #1 is supported; One-Line Mode #2 is not.
The sample rate to OMCK ratios and OMCK frequency requirements for Slave Mode operation are shown
in
Serial Audio Interface Signals
The CS42516 interfaces to an external Digital Audio Processor via two independent serial ports, the
CODEC serial port, CODEC_SP and the Serial Audio Interface serial port, SAI_SP. The digital output of
the internal ADCs can be configured to use either the CX_SDOUT pin or the SAI_SDOUT pin and the
corresponding serial port clocking signals. These configuration bits and the selection of Single-, Double-
or Quad-Speed Mode for CODEC_SP and SAI_SP are found in register
on page
The serial interface clocks, SAI_SCLK for SAI_SP and CX_SCLK for CODEC_SP, are used for transmit-
ting and receiving audio data. Either SAI_SCLK or CX_SCLK can be generated by the CS42516 (Master
Mode), or it can be input from an external source (Slave Mode). Master or Slave Mode selection is made
using bits CODEC_SP M/S and SAI_SP M/S in register
The Left/Right clock (SAI_LRCK or CX_LRCK) is used to indicate left and right data frames and the start
of a new sample period. It may be an output of the CS42516 (Master Mode), or it may be generated by
an external source (Slave Mode). As described in later sections, particular modes of operation do allow
the sample rate, Fs, of the SAI_SP and the CODEC_SP to be different, but must be multiples of each
other.
The serial data interface format selection (Left/Right-Justified, I²S or One-Line Mode) for the Serial Audio
Interface serial port data out pin, SAI_SDOUT, the CODEC serial port data out pin, CX_SDOUT, and the
CODEC input pins, CX_SDIN1:3, is configured using the appropriate bits in the register
mats (address 04h)” on page
the MSB first in all formats.
CX_SDIN1, CX_SDIN2, and CX_SDIN3 are the serial data input pins supplying the associated internal
DAC. CX_SDOUT, the ADC data output pin, carries data from the two internal 24-bit ADCs and, when
configured for one-line mode, up to four additional ADC channels attached externally to the signals
ADCIN1 and ADCIN2 (typically two CS5361 stereo ADCs). When operated in One-Line Mode, 6 channels
of DAC data are input on CX_SDIN1 and 6 channels of ADC data are output on CX_SDOUT.
page 28
Table
1. Refer to
48.
outlines the serial port channel allocations.
Table 3
32x, 48x, 64x, 128x
256x, 384x, 512x
Single-Speed
for required clock ratios.
50. The serial audio data is presented in two's complement binary form with
Table 3. Slave Mode Clock Ratios
128x, 192x, 256x
Double-Speed
32x, 48x, 64x
“Misc Control (address 05h)” on page
Quad-Speed
64x, 96x, 128x
32x, 48x, 64x
“Functional Mode (address 03h)”
One-Line Mode #1
“Interface For-
CS42516
256x
128x
Table 4 on
51.
27