AM29LV160DB-90EI Spansion Inc., AM29LV160DB-90EI Datasheet - Page 28
![no-image](/images/manufacturer_photos/0/6/621/spansion_inc__sml.jpg)
AM29LV160DB-90EI
Manufacturer Part Number
AM29LV160DB-90EI
Description
Flash Memory IC
Manufacturer
Spansion Inc.
Specifications of AM29LV160DB-90EI
Memory Configuration
2M X 8 / 1M X 16 Bit
Package/case
48-TSOP
Supply Voltage Max
3.6V
Access Time, Tacc
90nS
Mounting Type
Surface Mount
Supply Voltage
3V
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AM29LV160DB-90EI
Manufacturer:
AMD
Quantity:
20 000
DQ5: Exceeded Timing Limits
DQ5 indicates whether the program or erase time has
exceeded a specified internal pulse count limit. Under
these conditions DQ5 produces a “1.” This is a failure
condition that indicates the program or erase cycle was
not successfully completed.
The DQ5 failure condition may appear if the system
tries to program a “1” to a location that is previously pro-
grammed to “0.” Only an erase operation can change
a “0” back to a “1.” Under this condition, the device
halts the operation, and when the operation has
exceeded the timing limits, DQ5 produces a “1.”
Under both these conditions, the system must issue the
reset command to return the device to reading array
data.
DQ3: Sector Erase Timer
After writing a sector erase command sequence, the
system may read DQ3 to determine whether or not an
erase operation has begun. (The sector erase timer
does not apply to the chip erase command.) If additional
Notes:
1. DQ5 switches to ‘1’ when an Embedded Program or Embedded Erase operation has exceeded the maximum timing limits.
2. DQ7 and DQ2 require a valid address when reading status information. Refer to the appropriate subsection for further details.
28
Standard
Mode
Erase
Suspend
Mode
See “DQ5: Exceeded Timing Limits” for more information.
Embedded Program Algorithm
Embedded Erase Algorithm
Reading within Erase
Suspended Sector
Reading within Non-Erase
Suspended Sector
Erase-Suspend-Program
Operation
Table 10. Write Operation Status
(Note 2)
DQ7#
DQ7#
DQ7
Data
0
1
Am29LV160D
No toggle
Toggle
Toggle
Toggle
DQ6
Data
sectors are selected for erasure, the entire time-out also
applies after each additional sector erase command.
When the time-out is complete, DQ3 switches from “0” to
“1.” The system may ignore DQ3 if the system can
guarantee that the time between additional sector
erase commands will always be less than 50 s. See
also the “Sector Erase Command Sequence” section.
After the sector erase command sequence is written,
the system should read the status on DQ7 (Data# Poll-
ing) or DQ6 (Toggle Bit I) to ensure the device has ac-
cepted the command sequence, and then read DQ3. If
DQ3 is “1”, the internally controlled erase cycle has be-
gun; all further commands (other than Erase Suspend)
are ignored until the erase operation is complete. If
DQ3 is “0”, the device will accept additional sector
erase commands. To ensure the command has been
accepted, the system software should check the status
of DQ3 prior to and following each subsequent sector
erase command. If DQ3 is high on the second status
check, the last command might not have been ac-
cepted. Table 10 shows the outputs for DQ3.
(Note 1)
Data
DQ5
0
0
0
0
DQ3
Data
N/A
N/A
N/A
1
No toggle
(Note 2)
Toggle
Toggle
Data
DQ2
N/A
RY/BY#
0
0
1
1
0