AM29F160DT-90EI Spansion Inc., AM29F160DT-90EI Datasheet - Page 44

• Manufacturer Part Number: AM29F160DT-90EI
• Description: IC,EEPROM,NOR FLASH,1MX16/2MX8,CMOS,TSSOP,48PIN,PLASTIC
• Manufacturer: Spansion Inc.

Specifications of AM29F160DT-90EI

• Rohs Compliant: NO
• Cell Type: NOR
• Density: 16Mb
• Access Time (max): 90ns
• Interface Type: Parallel
• Boot Type: Top
• Address Bus: 21/20Bit
• Operating Supply Voltage (typ): 5V
• Operating Temp Range: -40C to 85C
• Package Type: TSOP
• Program/erase Volt (typ): 4.5 to 5.5V
• Sync/async: Asynchronous
• Operating Temperature Classification: Industrial
• Operating Supply Voltage (min): 4.5V
• Operating Supply Voltage (max): 5.5V
• Word Size: 8/16Bit
• Number Of Words: 2M/1M
• Supply Current: 50mA
• Mounting: Surface Mount
• Pin Count: 48
• Lead Free Status / Rohs Status: Not Compliant

ERASE AND PROGRAMMING PERFORMANCE
Notes:
1. Typical program and erase times assume the following conditions: 25
2. Under worst case conditions of 90°C, V
3. The typical chip programming time is considerably less than the maximum chip programming time listed, since most bytes
4. In the pre-programming step of the Embedded Erase algorithm, all bytes are programmed to 00h before erasure.
5. System-level overhead is the time required to execute the four-bus-cycle sequence for the program command. See
6. The device has a guaranteed minimum erase and
LATCHUP CHARACTERISTICS
Includes all pins except V
TSOP AND SO PIN CAPACITANCE
Notes:
1. Sampled, not 100% tested.
2. Test conditions T
DATA RETENTION
42
Parameter
Sector Erase Time
Chip Erase Time
Byte Programming Time
Word Programming Time
Chip Programming Time
(Note 2)
Input voltage with respect to V
(including A9, OE#, and RESET#)
Input voltage with respect to V
V
Minimum Pattern Data Retention Time
Parameter Symbol
CC
programming typicals assume checkerboard pattern.
program faster than the maximum program times listed.
for further information on command definitions.
program cycle endurance of 1,000,000 cycles.
Current
C
C
C
OUT
IN2
IN
(Note 2)
A
= 25°C, f = 1.0 MHz.
CC
SS
SS
. Test conditions: V
Parameter
Description
Word Mode
Byte Mode
on all pins except I/O pins
on all I/O pins
Control Pin Capacitance
Parameter Description
Output Capacitance
Input Capacitance
CC
Typ
= 4.5 V, 1,000,000 cycles.
CC
(Note 1)
1.0
25
11
15
12
= 5.0 V, one pin at a time.
7
D A T A S H E E T
Am29F160D
Max
300
360
(Note 3)
45
35
8
Test Conditions
°
150° C
125° C
C, 5.0 V V
Test Setup
V
V
V
OUT
IN
IN
–100 mA
–1.0 V
–1.0 V
= 0
= 0
Min
= 0
CC
Unit
µs
µs
, 1,000,000 cycles. Additionally,
s
s
s
s
Am29F160D_00_D10 April 23, 2010
Min
Excludes 00h programming prior
to erasure
Excludes system level overhead
(Note 5)
10
20
Typ
8.5
7.5
6
Comments
(Note 4)
V
CC
+100 mA
12.5 V
Max
Max
+ 1.0 V
7.5
12
9
Years
Years
Unit
Table 9
Unit
pF
pF
pF