AM29F040B-120JD Spansion Inc., AM29F040B-120JD Datasheet - Page 15
![Flash Memory IC](/photos/19/5/190510/4435482_sml.jpg)
AM29F040B-120JD
Manufacturer Part Number
AM29F040B-120JD
Description
Flash Memory IC
Manufacturer
Spansion Inc.
Datasheet
1.AM29F040B-120JD.pdf
(36 pages)
Specifications of AM29F040B-120JD
Memory Size
4Mbit
Memory Configuration
512K X 8
Ic Interface Type
Parallel
Access Time
120ns
Memory Case Style
PLCC
No. Of Pins
32
Operating Temperature Range
0°C To +70°C
Termination Type
SMD
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Command Definitions
Legend:
X = Don’t care
RA = Address of the memory location to be read.
RD = Data read from location RA during read operation.
PA = Address of the memory location to be programmed.
Addresses latch on the falling edge of the WE# or CE# pulse,
whichever happens later.
PD = Data to be programmed at location PA. Data latches on the
rising edge of WE# or CE# pulse, whichever happens first.
SA = Address of the sector to be verified (in autoselect mode) or
erased. Address bits A18–A16 select a unique sector.
Notes:
1. See Table 1 for description of bus operations.
2. All values are in hexadecimal.
3. Except when reading array or autoselect data, all bus cycles
4. Address bits A18–A11 are don’t cares for unlock and
5. No unlock or command cycles required when reading array data.
6. The Reset command is required to return to reading array
November 1, 2006 21445E5
Read (Note 5)
Reset (Note 6)
Program
Chip Erase
Sector Erase
Erase Suspend (Note 9)
Erase Resume (Note 10)
Autoselect
(Note 7)
are write operations.
command cycles, unless SA or PA required.
data when device is in the autoselect mode, or if DQ5 goes
high (while the device is providing status data).
Command
Sequence
(Note 1)
Manufacturer ID
Device ID
Sector Protect Verify
(Note 8)
Table 4. Am29F040B Command Definitions
1
1
4
4
4
4
6
6
1
1
Addr
XXX
555
555
555
555
555
555
XXX
XXX
RA
First
Data
D A T A
RD
AA
AA
AA
AA
AA
AA
B0
30
F0
Addr
2AA
2AA
2AA
2AA
2AA
2AA
Am29F040B
Second
Data
S H E E T
55
55
55
55
55
55
7. The fourth cycle of the autoselect command sequence is a
8. The data is 00h for an unprotected sector and 01h for a
9. The system may read and program in non-erasing sectors, or
10. The Erase Resume command is valid only during the Erase
read cycle.
protected sector.See “Autoselect Command Sequence” for
more information.
enter the autoselect mode, when in the Erase Suspend
mode. The Erase Suspend command is valid only during a
sector erase operation.
Suspend mode.
Addr
555
555
555
555
555
555
Bus Cycles (Notes 2–4)
Third
Data
90
90
90
A0
80
80
Addr
X00
X01
X02
555
555
SA
PA
Fourth
Data
PD
AA
AA
01
A4
00
01
Addr
2AA
2AA
Fifth
Data
55
55
Addr
555
SA
Sixth
Data
10
30
13