ADUM6132ARWZ-RL Analog Devices Inc, ADUM6132ARWZ-RL Datasheet - Page 4

• Manufacturer Part Number: ADUM6132ARWZ-RL
• Description: IC,Single MOSFET Driver,SOP,16PIN,PLASTIC
• Manufacturer: Analog Devices Inc
• Series: isoPower®r

Specifications of ADUM6132ARWZ-RL

• Inputs - Side 1/side 2: 2/0
• Number Of Channels: 2
• Isolation Rating: *
• Voltage - Supply: 4.5 V ~ 5.5 V
• Propagation Delay: 60ns
• Output Type: Logic
• Package / Case: 16-SOIC (0.300", 7.5mm Width)
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Number Of Outputs: 2
• Configuration: Half Bridge
• Input Type: Non-Inverting
• Delay Time: 60ns
• Current - Peak: 200mA
• Number Of Configurations: 1
• High Side Voltage - Max (bootstrap): 17V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

ADuM6132
Parameter
1
2
3
4
PACKAGE CHARACTERISTICS
Table 2.
Parameter
Resistance (Input Side to High-Side Output)
Capacitance (Input Side to High-Side Output)
Input Capacitance
Junction-to-Ambient Thermal Resistance
1
REGULATORY INFORMATION
The ADuM6132 is pending approval by the organizations listed in Table 3.
Table 3.
UL (Pending)
Recognized under UL 1577
component recognition program
Double/reinforced insulation,
3750 V rms isolation voltage
File E214100
1
2
INSULATION AND SAFETY RELATED SPECIFICATIONS
Table 4.
Parameter
Rated Dielectric Insulation Voltage
Minimum External Air Gap (Clearance)
Minimum External Tracking (Creepage)
Minimum Internal Gap (Internal Clearance)
Tracking Resistance (Comparative Tracking Index)
Isolation Group
See the
I
Duration less than 1 second. Average output current must conform to the limit shown in the
Undervoltage lockout (UVLO) holds the outputs in a low state if the corresponding input or output power supply is below the referenced threshold. Hysteresis is built
into the detection threshold to prevent oscillations and noise sensitivity.
The device is considered a two-terminal device: Pin 1 through Pin 8 are shorted together, and Pin 9 through Pin 16 are shorted together.
In accordance with UL 1577, each ADuM6132 is proof-tested by applying an insulation test voltage ≥4500 V rms for 1 second (current leakage detection limit = 10 μA).
In accordance with DIN V VDE V 0884-10, each ADuM6132 is proof-tested by applying an insulation test voltage ≥1050 V peak for 1 second (partial discharge detection
limit = 5 pC). The asterisk (*) marking branded on the component designates DIN V VDE V 0884-10 approval.
DDA
Part-to-Part Matching
Output Rise Time (10% to 90%)
Output Fall Time (10% to 90%)
is supplied by the output of the integrated isolated dc-to-dc power supply. I
Terminology
section.
1
1
CSA (Pending)
Approved under CSA Component Acceptance
Notice #5A
Basic insulation per CSA 60950-1-03 and IEC 60950-1,
800 V rms (1131 V peak) maximum working voltage
Reinforced insulation per CSA 60950-1-03 and
IEC 60950-1, 400 V rms maximum working voltage
File 205078
1
1
Symbol
t
t
R
F
Symbol
L(I01)
L(I02)
CTI
Symbol
R
C
C
θ
I-O
JA
I-O
I
Rev. 0 | Page 4 of 16
Min
Min
Value
3750
>8.0
>8.0
0.017 min
>175
IIIa
DDB
is supplied by an external power connection to the V
Absolute Maximum Ratings
Typ
10
2.0
4.0
45
Typ
Unit
V rms
mm
mm
mm
V
12
Max
60
15
15
Max
VDE (Pending)
Certified according to DIN V VDE V 0884-10
(VDE V 0884-10):2006-12
Reinforced insulation, 560 V peak
File 2471900-4880-0001
Measured from input terminals to output
terminals, shortest distance through air
Measured from input terminals to output
terminals, shortest distance path along body
Material Group (DIN VDE 0110, 1/89, Table 1)
Test Conditions/Comments
1 minute duration
Insulation distance through insulation
DIN IEC 112/VDE 0303 Part 1
section.
Unit
Ω
pF
pF
°C/W
Unit
ns
ns
ns
Test Conditions/Comments
C
C
C
Test Conditions/Comments
4-layer PCB
L
L
L
DDB
= 200 pF
= 200 pF
= 200 pF
pin. See Figure
2
16
.