ADUM5230ARWZ-RL Analog Devices Inc, ADUM5230ARWZ-RL Datasheet - Page 4
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
ADUM5230ARWZ-RL
Manufacturer Part Number
ADUM5230ARWZ-RL
Description
IC,Single MOSFET Driver,CMOS,SOP,16PIN,PLASTIC
Manufacturer
Analog Devices Inc
Series
iCoupler®r
Datasheet
1.ADUM5230ARWZ-RL.pdf
(16 pages)
Specifications of ADUM5230ARWZ-RL
Inputs - Side 1/side 2
2/0
Number Of Channels
2
Isolation Rating
2500Vrms
Voltage - Supply
4.5 V ~ 5.5 V
Propagation Delay
100ns
Output Type
Logic
Package / Case
16-SOIC (0.300", 7.5mm Width)
Operating Temperature
-40°C ~ 105°C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Data Rate
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
ADuM5230
Parameter
1
2
3
4
5
6
7
8
Short-circuit duration is less than 1 sec. Average output current must conform to the limit shown under the
The minimum pulse width is the shortest pulse width at which the specified timing parameters are guaranteed. Operation below the minimum pulse width is strongly
discouraged because in some instances pulse stretching to 1 μs may occur.
The maximum switching frequency is the maximum signal frequency at which the specified timing and power conversion parameters are guaranteed. Operation
above the maximum frequency is strongly discouraged.
t
measured from the 50% level of the rising edge of the V
In channel-to-channel matching, the rising or falling matching edge polarity is the magnitude of the propagation delay difference between two channels of the same
part when both inputs are either both rising or falling edges. The loads on each channel are equal.
In channel-to-channel matching, the rising vs. falling opposite edge polarity is the magnitude of the propagation delay difference between two channels of the same
part when one input is a rising edge and one input is a falling edge. The loads on each channel are equal.
In part-to-part matching, the rising or falling edges is the magnitude of the propagation delay difference between the same channels of two different parts when the
inputs are either both rising or falling edges. The supply voltages, temperatures, and loads of each part are equal.
In part-to-part matching, the rising vs. falling edges is the magnitude of the propagation delay difference between the same channels of two different parts when one
input is a rising edge and the other input is a falling edge. The supply voltages, temperatures, and loads of each part are equal.
PHL
Common-Mode Transient Immunity
Common-Mode Transient Immunity
Output Rise Time (10% to 90%)
Output Fall Time (10% to 90%)
propagation delay is measured from the 50% level of the falling edge of the V
at Logic High Output
at Logic Low Output
Ix
signal to the 50% level of the rising edge of the V
Symbol
|CM
|CM
t
t
R
F
H
L
|
|
Rev. 0 | Page 4 of 16
Min
25
25
Ix
signal to the 50% level of the falling edge of the V
Typ
35
35
Ox
Max
25
10
Absolute Maximum Ratings
signal.
Unit
kV/μs
kV/μs
ns
ns
Ox
Test Conditions
V
transient magnitude = 800 V
V
transient magnitude = 800 V
C
100 kHz switching frequency
C
100 kHz switching frequency
signal. t
Ix
Ix
L
L
section.
= 200 pF, I
= 200 pF, I
= V
= 0 V, V
DD1
PLH
, V
propagation delay is
CM
CM
= 1000 V,
ISO
ISO
= 1000 V,
= 10 mA,
= 10 mA,