AD9705-EBZ Analog Devices Inc, AD9705-EBZ Datasheet - Page 29
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
AD9705-EBZ
Manufacturer Part Number
AD9705-EBZ
Description
10-BIT Low Power TxDAC DAC IC
Manufacturer
Analog Devices Inc
Series
TxDAC®r
Datasheet
1.AD9704BCPZ.pdf
(52 pages)
Specifications of AD9705-EBZ
Number Of Dac's
1
Number Of Bits
10
Outputs And Type
1, Differential
Sampling Rate (per Second)
175M
Data Interface
Serial
Settling Time
11ns
Dac Type
Current
Voltage Supply Source
Analog and Digital
Operating Temperature
-40°C ~ 85°C
Utilized Ic / Part
AD9705
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
THEORY OF OPERATION
Figure 71 shows a simplified block diagram of the AD9707. The
AD9704/AD9705/AD9706/AD9707 consist of a DAC, digital
control logic, and full-scale output current control. The DAC
contains a PMOS current source array capable of providing a
nominal full-scale current (I
5 mA. The array is divided into 31 equal currents that make up the
five most significant bits (MSBs). The next four bits, or middle
bits, consist of 15 equal current sources whose value is 1/16 of an
MSB current source. The remaining LSBs are binary weighted frac-
tions of the current sources of the middle bits. Implementing the
middle and lower bits with current sources, instead of an R-2R
ladder, enhances the AD9704/AD9705/AD9706/AD9707 dynamic
performance for multitone or low amplitude signals and helps
maintain the high output impedance of the DAC (that is,
>200 MΩ).
All of these current sources are switched to one of the two
output nodes (IOUTA or IOUTB) via PMOS differential current
switches. The switches are based on the architecture pioneered
in the AD9764 family, with further refinements made to reduce
distortion contributed by the switching transient. This switch
architecture also reduces various timing errors and provides
matching complementary drive signals to the inputs of the
differential current switches.
The analog and digital sections of the AD9704/AD9705/AD9706/
AD9707 have separate power supply inputs (AVDD and DVDD)
that can operate independently over a 1.7 V to 3.6 V range. The
digital section, capable of operating at a rate of up to 175 MSPS,
consists of edge-triggered latches and segment decoding logic
circuitry. The analog section includes the PMOS current
sources, the associated differential switches, a 1.0 V band gap
voltage reference, and a reference control amplifier.
The DAC full-scale output current is regulated by the reference
control amplifier and can be set from 1 mA to 5 mA via an external
resistor, R
SET
, connected to the full-scale adjust (FS ADJ) pin.
OUTFS
R
) of 2 mA and a maximum of
SET
1.7V TO
0.1µF
1.7V
3.6V
CLK+
CLK–
TO
3.6V
REFIO
FS ADJ
CLKVDD
CLKCOM
DVDD
DCOM
1.0V REF
DIGITAL INPUTS (DB13 TO DB0) SLEEP/CSB
Figure 71. Simplified Block Diagram
SEGMENTED
SWITCHES
Rev. A | Page 29 of 52
LATCHES
AVDD
1.7V TO 3.6V
CURRENT
SOURCE
ARRAY
SWITCHES
LSB
The external resistor, in combination with both the reference
control amplifier and voltage reference, V
current, I
with the proper scaling factor. The full-scale current, I
32 × I
The AD9704/AD9705/AD9706/AD9707 provide the option of
setting the output common mode to a value other than ACOM
via the output common mode (OTCM) pin. This facilitates
interfacing the output of the AD9704/AD9705/AD9706/AD9707
directly to components that require common-mode levels greater
than 0 V.
SERIAL PERIPHERAL INTERFACE
The AD9704/AD9705/AD9706/AD9707 serial port is a flexible,
synchronous serial communications port allowing easy interfacing
to many industry-standard microcontrollers and microprocessors.
The serial I/O is compatible with most synchronous transfer
formats, including the Motorola SPI and Intel® SSR protocols.
The interface allows read/write access to all registers that configure
the AD9704/AD9705/AD9706/AD9707. Single or multiple byte
transfers are supported, as well as MSB first or LSB first transfer
formats. The serial interface port of the AD9704/AD9705/AD9706/
AD9707 is configured as a single pin I/O.
General Operation of the Serial Interface
There are two phases to a communication cycle with the
AD9704/AD9705/AD9706/AD9707. Phase 1 is the instruction
cycle, which is the writing of an instruction byte into the
AD9704/AD9705/AD9706/AD9707, coincident with the first
eight SCLK rising edges. The instruction byte provides the
AD9704/AD9705/AD9706/AD9707 serial port controller with
information regarding the data transfer cycle, which is Phase 2
of the communication cycle. The Phase 1 instruction byte defines
whether the upcoming data transfer is read or write, the number
of bytes in the data transfer, and the starting register address for
the first byte of the data transfer.
ACOM
AD9707
REF
.
SPI
REF
OTCM
IOUTA
IOUTB
, which is replicated to the segmented current sources
AD9704/AD9705/AD9706/AD9707
PIN/SPI/RESET
MODE/SDIO
CMODE/SCLK
REFIO
, sets the reference
OUTFS
, is