AD9609-20EBZ Analog Devices Inc, AD9609-20EBZ Datasheet - Page 25
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
AD9609-20EBZ
Manufacturer Part Number
AD9609-20EBZ
Description
10 Bit 20 Msps Low Pwr ADC
Manufacturer
Analog Devices Inc
Datasheet
1.AD9609BCPZ-20.pdf
(32 pages)
Specifications of AD9609-20EBZ
Number Of Adc's
1
Number Of Bits
10
Sampling Rate (per Second)
20M
Data Interface
Serial, SPI™
Inputs Per Adc
1 Differential
Input Range
2 Vpp
Power (typ) @ Conditions
46.3mW @ 20MSPS
Voltage Supply Source
Analog and Digital
Operating Temperature
-40°C ~ 85°C
Utilized Ic / Part
AD9609
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
SERIAL PORT INTERFACE (SPI)
The AD9609 serial port interface (SPI) allows the user to configure
the converter for specific functions or operations through a
structured register space provided inside the ADC. The SPI
gives the user added flexibility and customization, depending
on the application. Addresses are accessed via the serial port
and can be written to or read from via the port. Memory is
organized into bytes that can be further divided into fields,
which are documented in the Memory Map section. For
detailed operational information, see the AN-877 Applica-
tion Note, Interfacing to High Speed ADCs via SPI.
CONFIGURATION USING THE SPI
Three pins define the SPI of this ADC: SCLK, SDIO, and CSB
(see Table 14). The SCLK (a serial clock) is used to synchronize
the read and write data presented from and to the ADC. SDIO
(serial data input/output) is a dual-purpose pin that allows data to
be sent and read from the internal ADC memory map registers.
The CSB (chip select bar) is an active-low control that enables
or disables the read and write cycles.
Table 14. Serial Port Interface Pins
Pin
SCLK
SDIO
CSB
SCLK
SDIO
CSB
DON’T CARE
DON’T CARE
Function
Serial clock. The serial shift clock input, which is used to
synchronize serial interface reads and writes.
Serial data input/output. A dual-purpose pin that
typically serves as an input or an output, depending on
the instruction being sent and the relative position in the
timing frame.
Chip select bar. An active-low control that gates the read
and write cycles.
t
S
R/W
t
DS
W1
W0
t
DH
A12
t
HIGH
A11
Figure 54. Serial Port Interface Timing Diagram
t
LOW
A10
A9
Rev. 0 | Page 25 of 32
t
CLK
A8
A7
The falling edge of CSB, in conjunction with the rising edge of
SCLK, determines the start of the framing. An example of the
serial timing and its definitions can be found in Figure 54 and
Table 5.
Other modes involving the CSB are available. The CSB can be
held low indefinitely, which permanently enables the device;
this is called streaming. The CSB can stall high between bytes to
allow for additional external timing. When CSB is tied high, SPI
functions are placed in high impedance mode. This mode turns
on any SPI pin secondary functions.
During an instruction phase, a 16-bit instruction is transmitted.
Data follows the instruction phase, and its length is determined
by the W0 and W1 bits, as shown in Figure 54.
All data is composed of 8-bit words. The first bit of the first byte in
a multibyte serial data transfer frame indicates whether a read
command or a write command is issued. This allows the serial
data input/output (SDIO) pin to change direction from an input
to an output at the appropriate point in the serial frame.
In addition to word length, the instruction phase determines
whether the serial frame is a read or write operation, allowing
the serial port to be used both to program the chip and to read
the contents of the on-chip memory. If the instruction is a readback
operation, performing a readback causes the serial data input/
output (SDIO) pin to change direction from an input to an output
at the appropriate point in the serial frame.
Data can be sent in MSB-first mode or in LSB-first mode. MSB
first is the default on power-up and can be changed via the SPI
port configuration register. For more information about this
and other features, see the AN-877 Application Note, Interfacing
to High Speed ADCs via SPI.
D5
D4
D3
D2
D1
D0
t
H
DON’T CARE
AD9609
DON’T CARE