AD9520-5BCPZ Analog Devices Inc, AD9520-5BCPZ Datasheet - Page 26

• Manufacturer Part Number: AD9520-5BCPZ
• Description: 12/24-Output Clock Generator
• Manufacturer: Analog Devices Inc
• Type: Clock Generator, Fanout Distributionr

Specifications of AD9520-5BCPZ

• Design Resources: Synchronizing Multiple AD9910 1 GSPS Direct Digital Synthesizers (CN0121) Phase Coherent FSK Modulator (CN0186)
• Pll: Yes
• Input: CMOS, LVDS, LVPECL
• Output: CMOS, LVPECL
• Number Of Circuits: 1
• Ratio - Input:output: 2:12, 2:24
• Differential - Input:output: Yes/Yes
• Frequency - Max: 2.4GHz
• Divider/multiplier: Yes/No
• Voltage - Supply: 3.135 V ~ 3.465 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 64-LFCSP
• Frequency-max: 1.6GHz
• Function: Clock Generator
• Operating Temperature (max): 85C
• Operating Temperature (min): -40C
• Package Type: LFCSP EP
• Pin Count: 64
• Mounting: Surface Mount
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

AD9520-5
THEORY OF OPERATION
OPERATIONAL CONFIGURATIONS
The AD9520 can be configured in several ways. These
configurations must be set up by loading the control registers
(see Table 44 to Table 55). Each section or function must be
individually programmed by setting the appropriate bits in the
corresponding control register or registers. When the desired
configuration is programmed, the user can store these values in
the on-board EEPROM to allow the part to power up in the desired
configuration without user intervention.
Mode 1: Clock Distribution or External VCO < 1600 MHz
When the external clock source to be distributed or the external
VCO/VCXO is <1600 MHz, a configuration that bypasses the
VCO divider can be used. This is the only difference from Mode 2.
Bypassing the VCO divider limits the frequency of the clock
source to <1600 MHz (due to the maximum input frequency
allowed at the channel dividers).
Configuration and Register Settings
For clock distribution applications where the external clock is
<1600 MHz, the register settings shown in Table 19 should be used.
Table 19. Settings for Clock Distribution < 1600 MHz
Register
0x010[1:0] = 01b
0x1E1[0] = 1b
0x1E1[1] = 0b
Description
PLL asynchronous power-down (PLL off )
Bypass the VCO divider as the source for
the distribution section
CLK selected as the source
Rev. 0 | Page 26 of 80
When using the internal PLL with an external VCO < 1600 MHz,
the PLL must be turned on.
Table 20. Settings for Using Internal PLL with External VCO
< 1600 MHz
Register
0x1E1[0] = 1b
0x010[1:0] = 00b
An external VCO/VCXO requires an external loop filter that
must be connected between CP and the tuning pin of the VCO/
VCXO. This loop filter determines the loop bandwidth and stability
of the PLL. Make sure to select the proper PFD polarity for the
VCO/VCXO being used.
Table 21. Setting the PFD Polarity
Register
0x010[7] = 0b
0x010[7] = 1b
Description
PFD polarity positive (higher control voltage
produces higher frequency)
PFD polarity negative (higher control voltage
produces lower frequency)
Description
Bypass the VCO divider as the source for
the distribution section
PLL normal operation (PLL on) along
with other appropriate PLL settings in
0x010 to 0x01E