AD9248BCPZRL-65 Analog Devices Inc, AD9248BCPZRL-65 Datasheet - Page 20
![IC,A/D CONVERTER,DUAL,14-BIT,CMOS,LLCC,64PIN](/photos/6/50/65021/505-64-lfcsp_sml.jpg)
AD9248BCPZRL-65
Manufacturer Part Number
AD9248BCPZRL-65
Description
IC,A/D CONVERTER,DUAL,14-BIT,CMOS,LLCC,64PIN
Manufacturer
Analog Devices Inc
Datasheet
1.AD9248BSTZ-20.pdf
(48 pages)
Specifications of AD9248BCPZRL-65
Number Of Bits
14
Sampling Rate (per Second)
65M
Data Interface
Parallel
Number Of Converters
2
Power Dissipation (max)
600mW
Voltage Supply Source
Single Supply
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
64-LFCSP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
AD9248BST-65EBZ - BOARD EVAL WITH AD9248BST-65AD9248BCP-65EBZ - BOARD EVAL WITH AD9248BCP-65
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
AD9248
DATA FORMAT
The AD9248 data output format can be configured for either
twos complement or offset binary. This is controlled by the data
format select pin (DFS). Connecting DFS to AGND produces
offset binary output data. Conversely, connecting DFS to AVDD
formats the output data as twos complement.
The output data from the dual ADCs can be multiplexed onto a
single 14-bit output bus. The multiplexing is accomplished by
toggling the MUX_SELECT bit, which directs channel data to
the same or opposite channel data port. When MUX_SELECT
is logic high, the Channel A data is directed to the Channel A
output bus, and the Channel B data is directed to the Channel B
output bus. When MUX_SELECT is logic low, the channel data
is reversed, that is, the Channel A data is directed to the
Channel B output bus, and the Channel B data is directed to the
Channel A output bus. By toggling the MUX_SELECT bit,
multiplexed data is available on either of the output data ports.
If the ADCs run with synchronized timing, this same clock can
be applied to the MUX_SELECT pin. Any skew between
CLK_A, CLK_B, and MUX_SELECT can degrade AC
performance. It is recommended to keep the clock skew
<100 pS. After the MUX_SELECT rising edge, either data port
has the data for its respective channel; after the falling edge, the
alternate channel’s data is placed on the bus. Typically, the other
unused bus would be disabled by setting the appropriate OEB
high to reduce power consumption and noise. Figure 34 shows
an example of multiplex mode. When multiplexing data, the
data rate is two times the sample rate. Note that both channels
must remain active in this mode and that each channel’s power-
down pin must remain low.
VOLTAGE REFERENCE
A stable and accurate 0.5 V voltage reference is built into the
AD9248. The input range can be adjusted by varying the
reference voltage applied to the AD9248, using either the
internal reference with different external resistor configurations
or an externally applied reference voltage. The input span of the
ADC tracks reference voltage changes linearly. If the ADC is
being driven differentially through a transformer, the reference
voltage can be used to bias the center tap (common-mode
voltage).
The shared reference mode allows the user to connect the
references from the dual ADCs together externally for superior
Table 7. Reference Configuration Summary
Selected Mode
External Reference
Internal Fixed Reference
Programmable Reference
Internal Fixed Reference
SENSE Voltage
AVDD
V
0.2 V to V
AGND to 0.2 V
REF
REF
Rev. B | Page 20 of 48
Resulting V
N/A
0.5
0.5 × (1 + R2/R1)
1.0
REF
gain and offset matching performance. If the ADCs are to
function independently, the reference decoupling can be
treated independently and can provide superior isolation
between the dual channels. To enable shared reference mode,
the SHARED_REF pin must be tied high and the external
differential references must be externally shorted. (REFT_A
must be externally shorted to REFT_B, and REFB_A must be
shorted to REFB_B.)
Internal Reference Connection
A comparator within the AD9248 detects the potential at the
SENSE pin and configures the reference into four possible
states, which are summarized in Table 7. If SENSE is grounded,
the reference amplifier switch is connected to the internal
resistor divider (see Figure 35), setting VREF to 1 V.
Connecting the SENSE pin to VREF switches the reference
amplifier output to the SENSE pin, completing the loop and
providing a 0.5 V reference output. If a resistor divider is
connected, as shown in Figure 36, the switch is again set to the
SENSE pin. This puts the reference amplifier in a noninverting
mode with the VREF output defined as
In all reference configurations, REFT and REFB drive the ADC
core and establish its input span. The input range of the ADC
always equals twice the voltage at the reference pin for either an
internal or an external reference.
10μF
(V)
V
REF
= 0.5 × (1 + R2/R1)
SENSE
0.1μF
VIN+
VIN–
VREF
Figure 35. Internal Reference Configuration
Resulting Differential Span (V p-p)
2 × External Reference
1.0
2 × V
2.0
REF
SELECT
LOGIC
(See Figure 36)
AD9248
0.5V
CORE
ADC
REFB
REFT
0.1μF
0.1μF
0.1μF
10μF