AD9212ABCPZ-65 Analog Devices Inc, AD9212ABCPZ-65 Datasheet - Page 22
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
AD9212ABCPZ-65
Manufacturer Part Number
AD9212ABCPZ-65
Description
Octal 10 Bit, 65 MSPS Serial LVDS ADC
Manufacturer
Analog Devices Inc
Datasheet
1.AD9212ABCPZRL7-40.pdf
(56 pages)
Specifications of AD9212ABCPZ-65
Number Of Bits
10
Sampling Rate (per Second)
65M
Data Interface
Serial, SPI™
Number Of Converters
8
Power Dissipation (max)
833mW
Voltage Supply Source
Analog and Digital
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
64-LFCSP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
AD9212
CLOCK INPUT CONSIDERATIONS
For optimum performance, the AD9212 sample clock inputs
(CLK+ and CLK−) should be clocked with a differential signal.
This signal is typically ac-coupled into the CLK+ and CLK− pins
via a transformer or capacitors. These pins are biased internally
and require no additional biasing.
Figure 51 shows the preferred method for clocking the AD9212.
The low jitter clock source is converted from single-ended to
differential using an RF transformer. The back-to-back Schottky
diodes across the secondary transformer limit clock excursions
into the AD9212 to approximately 0.8 V p-p differential. This
helps prevent the large voltage swings of the clock from feeding
through to other portions of the AD9212, and it preserves the
fast rise and fall times of the signal, which are critical to low
jitter performance.
Another option is to ac-couple a differential PECL signal to the
sample clock input pins as shown in Figure 52. The AD9510/
AD9511/AD9512/AD9513/AD9514/AD9515
drivers offers excellent jitter performance.
1
1
50Ω RESISTORS ARE OPTIONAL.
50Ω RESISTORS ARE OPTIONAL.
CLK+
CLK+
CLK–
CLK+
CLK–
50Ω
50Ω
1
1
50Ω
Figure 51. Transformer-Coupled Differential Clock
0.1µF
Figure 53. Differential LVDS Sample Clock
Figure 52. Differential PECL Sample Clock
50Ω
0.1µF
0.1µF
0.1µF
0.1µF
50Ω
100Ω
ADT1–1WT, 1:1Z
1
1
Mini-Circuits
CLK
CLK
CLK
CLK
LVDS DRIVER
PECL DRIVER
XFMR
0.1µF
AD9510/AD9511/
AD9512/AD9513/
AD9514/AD9515
AD9510/AD9511/
AD9512/AD9513/
AD9514/AD9515
240Ω
®
0.1µF
0.1µF
SCHOTTKY
HSM2812
DIODES:
240Ω
100Ω
100Ω
0.1µF
0.1µF
0.1µF
0.1µF
family of clock
CLK+
CLK–
AD9212
CLK+
CLK–
CLK+
CLK–
ADC
AD9212
AD9212
ADC
ADC
Rev. D | Page 22 of 56
In some applications, it is acceptable to drive the sample clock
inputs with a single-ended CMOS signal. In such applications,
CLK+ should be driven directly from a CMOS gate, and the
CLK− pin should be bypassed to ground with a 0.1 μF capacitor
in parallel with a 39 kΩ resistor (see Figure 54). Although the
CLK+ input circuit supply is AVDD (1.8 V), this input is
designed to withstand input voltages of up to 3.3 V, making the
selection of the drive logic voltage very flexible.
Clock Duty Cycle Considerations
Typical high speed ADCs use both clock edges to generate a
variety of internal timing signals. As a result, these ADCs may
be sensitive to the clock duty cycle. Commonly, a 5% tolerance is
required on the clock duty cycle to maintain dynamic performance
characteristics. The AD9212 contains a duty cycle stabilizer (DCS)
that retimes the nonsampling edge, providing an internal clock
signal with a nominal 50% duty cycle. This allows a wide range
of clock input duty cycles without affecting the performance of
the AD9212. When the DCS is on, noise and distortion perfor-
mance are nearly flat for a wide range of duty cycles. However,
some applications may require the DCS function to be off. If so,
keep in mind that the dynamic range performance can be affected
when operated in this mode. See the Memory Map section for
more details on using this feature.
The duty cycle stabilizer uses a delay-locked loop (DLL) to
create the nonsampling edge. As a result, any changes to the
sampling frequency require approximately eight clock cycles
to allow the DLL to acquire and lock to the new rate.
CLK+
CLK+
1
50Ω RESISTOR IS OPTIONAL.
1
50Ω RESISTOR IS OPTIONAL.
50Ω
50Ω
0.1µF
0.1µF
Figure 54. Single-Ended 1.8 V CMOS Sample Clock
Figure 55. Single-Ended 3.3 V CMOS Sample Clock
1
1
0.1µF
0.1µF
CLK
CLK
CLK
CLK
CMOS DRIVER
CMOS DRIVER
AD9510/AD9511/
AD9512/AD9513/
AD9514/AD9515
AD9510/AD9511/
AD9512/AD9513/
AD9514/AD9515
0.1µF
OPTIONAL
OPTIONAL
100Ω
100Ω
39kΩ
0.1µF
0.1µF
0.1µF
CLK+
CLK–
CLK+
CLK–
AD9212
AD9212
ADC
ADC