AD8310ARMZ-REEL7 Analog Devices Inc, AD8310ARMZ-REEL7 Datasheet - Page 21

• Manufacturer Part Number: AD8310ARMZ-REEL7
• Description: IC,Log/Antilog Amplifier,SINGLE,BIPOLAR,TSSOP,8PIN,PLASTIC
• Manufacturer: Analog Devices Inc
• Type: Logarithmic Amplifierr

Specifications of AD8310ARMZ-REEL7

• Applications: Receiver Signal Strength Indication (RSSI)
• Mounting Type: Surface Mount
• Package / Case: 8-MSOP, Micro8™, 8-uMAX, 8-uSOP,
• Number Of Channels: 1
• Number Of Elements: 6
• Power Supply Requirement: Single
• Input Resistance: 0.0012@5VMohm
• Single Supply Voltage (typ): 3/5V
• Dual Supply Voltage (typ): Not RequiredV
• Power Dissipation: 200mW
• Rail/rail I/o Type: Rail to Rail Input
• Single Supply Voltage (min): 2.7V
• Single Supply Voltage (max): 5.5V
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 8
• Package Type: MSOP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Table 6. Evaluation Board Setup Options
Component
TP1, TP2
SW1
R1/R4
C1, C2, R3
C3
C4, C5, R5
R6
W1, W2, C6, R7
C7
Function
Supply and Ground Vector Pins.
Device Enable. When in Position A, the ENBL pin is connected to +V
operating mode. When in Position B, the ENBL pin is connected to ground, putting the device into
sleep mode.
SMA Connector Grounds. Connects common of INHI and INLO SMA connectors to ground. They
can be used to isolate the generator ground from the evaluation board ground. See Figure 28.
Input Interface. R3 (52.3 Ω) combines with the AD8310’s 1 kΩ input impedance to give an overall
broadband input impedance of 50 Ω. C1, C2, and the AD8310’s input impedance combine to set a
high-pass input corner of 32 kHz. Alternatively, R3, C1, and C2 can be replaced by an inductor and
matching capacitors to form an input matching network. See the Input Matching section for details.
RSSI (Video) Bandwidth Adjust. The addition of C3 (farads) lowers the RSSI bandwidth of the
AD8310’s output according to the following equation:
Supply Decoupling. The normal supply decoupling of 0.01 μF (C4) can be augmented by a larger
capacitor in C5. An inductor or small resistor can be placed in R5 for additional decoupling.
Output Source Impedance. In cable-driving applications, a resistor (typically 50 Ω or 75 Ω) can be
placed in R6 to give the circuit a back-terminated output impedance.
Output Loading. Resistors and capacitors can be placed in C6 and R7 to load-test VOUT. Jumper W1
and Jumper W2 are used to connect or disconnect the loads.
Offset Compensation Loop. A capacitor in C7 reduces the corner frequency of the offset control
loop in low frequency applications.
C
FILT
= 1/(2π × 3 kΩ Video Bandwidth) − 2.1 pF
Rev. F | Page 21 of 24
S
, and the AD8310 is in normal
Default Condition
Not applicable
SW1 = A
R1 = R4 = 0 Ω
R3 = 52.3 Ω,
C1 = C2 = 0.01 μF
C3 = open
C4 = 0.01 μF,
C5 = open, R5 = 0 Ω
R6 = 0 Ω
C6 = R7 = open,
W1 = W2 = installed
C7 = open
AD8310