AD8231ACPZ-RL Analog Devices Inc, AD8231ACPZ-RL Datasheet - Page 22
![IC,Instrumentation Amplifier,SINGLE,LLCC,16PIN,PLASTIC](/photos/6/50/65061/505-16-lfcsp_sml.jpg)
AD8231ACPZ-RL
Manufacturer Part Number
AD8231ACPZ-RL
Description
IC,Instrumentation Amplifier,SINGLE,LLCC,16PIN,PLASTIC
Manufacturer
Analog Devices Inc
Datasheet
1.AD8231-EVALZ.pdf
(24 pages)
Specifications of AD8231ACPZ-RL
Amplifier Type
Instrumentation
Number Of Circuits
2
Output Type
Rail-to-Rail
Slew Rate
1.1 V/µs
Gain Bandwidth Product
7MHz
Current - Input Bias
250pA
Voltage - Input Offset
4µV
Current - Supply
4mA
Current - Output / Channel
70mA
Voltage - Supply, Single/dual (±)
3 V ~ 6 V, ±1.5 V ~ 3 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
16-LFCSP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
AD8231-EVALZ - BOARD EVAL FOR AD8231
-3db Bandwidth
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
AD8231
When operating the AD8231 on dual supplies, a level-shift is
typically needed from standard single-supply control logic. One
easy way to accomplish the level-shift is through a single-pole,
double-throw switch, such as the
application schematic for ±2.5 V operation.
SALLEN KEY FILTER
The extra op amp in the AD8231 can be used to create a 2-pole
Sallen Key filter. Such a filter can remove excess noise or
perform antialiasing before an analog-to-digital converter.
Figure 56 shows how to create a 2-pole low-pass Butterworth
filter. Components R1, R2, C1, and C2 set the frequency of the
filter. The ratio of R3 and R4 sets the peaking of the filter. If R4
equals 10 kΩ, R3 should equal 5.9 kΩ for an optimum 2-pole
response.
Depending on the circuitry before and after the AD8231,
a 3-pole filter can be possible. If the previous stage has a small
output impedance, an additional pole can be added before the
in amp (R6, R7, and C4). If the following stage has a high input
impedance, an additional pole can be added after the op amp
(R5 and C3). Peaking from the Sallen Key stage should be
higher to compensate for the extra attenuation of the third pole;
both R3 and R4 should be 10 kΩ for optimum response.
V
ANY VOLTAGE BETWEEN 2.5V AND 9.5V.
MICROCONTROLLER,
DIGITAL
Figure 55. Converting Single-Supply Control Signals to Dual Supply.
CONTROL
DIGITAL
V
(FPGA,
IS THE DIGITAL SUPPLY VOLTAGE. IT CAN BE
DIGITAL
ETC.)
GND
V
DD
+2.5V
–2.5V
+2.5V
–2.5V
+2.5V
–2.5V
A0
A1
A2
EN
–2.5V
ADG633
V
V
SS
DIGITAL
V
DD
GND
ADG633. Figure 55 shows an
AD8231
A0 A1 A2
SDN
+V
–V
CS
S
S
+2.5V
–2.5V
Rev. A | Page 22 of 24
Note that in addition to setting the peaking of the filter, the
ratio R3/R4 also sets the dc gain: G = 1 + R3/R4. If lower dc
gain is required, replace R1 with a voltage divider, where the
output resistance of the divider is equal to the required value of R1.
Figure 56 shows a bias point connected to R4 and the in-amp
reference. The filter stage amplifies the signal around this bias
point. The bias point is typically midsupply and should be low
impedance.
Table 10. Recommended Component Values for Butterworth
Low-Pass Filter in Figure 56
3 dB
Freq
32 Hz
100 Hz
320 Hz
1 kHz
3.2 kHz
10 kHz
32 kHz
Figure 56. Butterworth Low-Pass Filter (Dotted Sections Indicate Optional Poles)
OPTIONAL POLE
R6
R7
C4
Sallen Key
R1, R2
(kΩ)
499
158
49.9
158
49.9
15.8
4.99
IN-AMP
POINT
BIAS
C1, C2
(nF)
10
10
10
1
1
1
1
REF
R1
Before In-Amp
R6, R7
(kΩ)
499
158
49.9
158
49.9
15.8
4.99
R2
C2
SALLEN KEY
(TWO POLE)
OP AMP
Optional Poles
C4
(nF)
4.7
4.7
4.7
0.47
0.47
0.47
0.47
C1
POINT
BIAS
After Op Amp
R5
(kΩ)
49.9
16
4.99
1.6
0.499
0.16
0.049
OPTIONAL POLE
R3
R4
R5
C3
C3
(nF)
100
100
100
100
100
100
100