AD8223ARM Analog Devices Inc, AD8223ARM Datasheet - Page 15

• Manufacturer Part Number: AD8223ARM
• Description: Single Supply Low Cost Intrumentation Am
• Manufacturer: Analog Devices Inc

Specifications of AD8223ARM

• Amplifier Type: Instrumentation
• Number Of Circuits: 1
• Output Type: Rail-to-Rail
• Slew Rate: 0.3 V/µs
• -3db Bandwidth: 200kHz
• Current - Input Bias: 12nA
• Voltage - Input Offset: 250µV
• Current - Supply: 650µA
• Voltage - Supply, Single/dual (±): 3 V ~ 24 V, ±2 V ~ 12 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 8-MSOP, Micro8™, 8-uMAX, 8-uSOP,
• Peak Reflow Compatible (260 C): No
• Rohs Compliant: No
• Input Offset Voltage: 250µV
• Bandwidth: 200kHz
• Amplifier Output: Rail To Rail
• Cmrr: 90dB
• Supply Current: 350µA
• Amplifier Case Style: MSOP
• No. Of Pins: 8
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Current - Output / Channel: -
• Gain Bandwidth Product: -
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant, Contains lead / RoHS non-compliant

REFERENCE TERMINAL
The output voltage of the AD8223 is developed with respect to
the potential on the reference terminal. This is useful when the
output signal needs to be offset to a precise midsupply level. For
example, a voltage source can be tied to the REF pin to level-
shift the output so that the AD8223 can drive a single-supply
ADC. The REF pin is protected with ESD diodes and should
not exceed either +V
For best performance, keep the source impedance to the REF
terminal below 5 Ω. As shown in Figure 31, the reference
terminal, REF, is at one end of a 50 kΩ resistor. Additional
impedance at the REF terminal adds to this resistor and results
in poorer CMRR performance.
INPUT PROTECTION
Internal supply referenced clamping diodes allow the input,
reference, output, and gain terminals of the AD8223 to safely
withstand overvoltages of 0.3 V above or below the supplies.
This is true for all gains, and for power-on and power-off. This
last case is particularly important because the signal source and
amplifier can be powered separately.
If the overvoltage is expected to exceed this value, limit the
current through these diodes to about 10 mA using external
current limiting resistors. This is shown in Figure 33. The size
of this resistor is defined by the supply voltage and the required
overvoltage protection.
V
V
OVER
OVER
V
REF
INCORRECT
R
R
LIM
LIM
AD8223
Figure 32. Driving the Reference Pin
1 = 10mA MAX
S
Figure 33. Input Protection
or −V
R
G
S
by more than 0.3 V.
V
REF
+
–
+
OP2177
–
CORRECT
+V
–V
AD8223
S
S
R
AD8223
LIM
=
V
OVER
10mA
– V
OUT
S
+ 0.7V
Rev. 0 | Page 15 of 20
RF INTERFERENCE (RFI)
RF rectification is often a problem when amplifiers are used in
applications where there are strong RF signals. The disturbance
can appear as a small dc offset voltage. High frequency signals
can be filtered with a low-pass, R-C network placed at the input
of the instrumentation amplifier, as shown in Figure 34. The
filter limits the input signal bandwidth according to the follow-
ing relationship:
where C
Figure 34 shows an example in which the differential filter fre-
quency is approximately 400 Hz, and the common-mode filter
frequency is approximately 40 kHz. The typical dc offset shift
over frequency is less than 1.5 μV, and the RF signal rejection
of the circuit is better than 71 dB.
The resistors were selected to be large enough to isolate the
circuit input from the capacitors but not large enough to
significantly increase the circuit noise. Choose values of R and
C
input and the R × C
the AD8223. Because of their higher accuracy and stability,
COG/NPO type ceramic capacitors are recommended for the
C
critical.
C
C
to minimize RFI. Mismatch between the R × C
capacitors. The dielectric for the C
FilterFreq
FilterFreq
D
≥ 10C
4.02kΩ
4.02kΩ
R
R
Diff
CM
C
.


C
2
C
1nF
C
47nF
C
1nF
2
Figure 34. RFI Suppression

C
D
C
at negative input degrades the CMRR of

RC
1
R
(2
499Ω
C
C
R1
1
0.1µF
0.1µF
D
+IN
–IN

C
+
–
C
AD8223
)
+15V
–15V
D
capacitor is not as
REF
10µF
10µF
V
C
OUT
+
+
at positive
AD8223