AD7247KRZ Analog Devices Inc, AD7247KRZ Datasheet - Page 8
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
AD7247KRZ
Manufacturer Part Number
AD7247KRZ
Description
IC,D/A CONVERTER,DUAL,12-BIT,BICMOS,SOP,24PIN
Manufacturer
Analog Devices Inc
Series
DACPORT®r
Specifications of AD7247KRZ
Settling Time
10µs
Number Of Bits
12
Data Interface
Parallel
Number Of Converters
2
Voltage Supply Source
Dual ±
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
24-SOIC (7.5mm Width)
Number Of Channels
2
Resolution
12b
Interface Type
Parallel
Single Supply Voltage (typ)
15V
Dual Supply Voltage (typ)
±15V
Architecture
R-2R
Power Supply Requirement
Single/Dual
Output Type
Voltage
Single Supply Voltage (min)
14.25V
Single Supply Voltage (max)
15.75V
Dual Supply Voltage (min)
±14.25V
Dual Supply Voltage (max)
±15.75V
Operating Temp Range
-40C to 85C
Operating Temperature Classification
Industrial
Mounting
Surface Mount
Pin Count
24
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Power Dissipation (max)
-
Lead Free Status / Rohs Status
Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AD7247KRZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
AD7237A/AD7247A
CIRCUIT INFORMATION
D/A Section
The AD7237A/AD7247A contains two 12-bit voltage-mode D/A
converters consisting of highly stable thin film resistors and high
speed NMOS single-pole, double-throw switches. The output
voltage from the converters has the same polarity as the refer-
ence voltage, REF IN, allowing single supply operation. The
simplified circuit diagram for one of the D/A converters is
shown in Figure 2.
The REF IN voltage is internally buffered by a unity gain
amplifier before being applied to the D/A converters. The D/A
converters are configured and scaled for a 5 V reference and the
device is tested with 5 V applied to REF IN.
Internal Reference
The AD7237A/AD7247A has an on-chip temperature compen-
sated buried Zener reference (see Figure 3) which is factory
trimmed to 5 V 30 mV ( 50 mV for T Version). The reference
voltage is provided at the REF OUT pin. This reference can be
used to provide the reference voltage for the D/A converter (by
connecting the REF OUT pin to the REF IN pin) and the offset
voltage for bipolar outputs (by connecting REF OUT to R
The reference voltage can also be used as a reference for other
components and is capable of providing up to 500 A to an ex-
ternal load. The maximum recommended capacitance on REF
OUT for normal operation is 50 pF. If the reference is required
for external use, it should be decoupled to AGND (GND) with
a 200
tantalum capacitor and a 0.1 F ceramic capacitor.
resistor in series with parallel combination of a 10 F
Figure 2. D/A Simplified Circuit Diagram
Figure 3. Internal Reference
OFS
).
–8–
External Reference
In some applications, the user may require a system reference or
some other external reference to drive the AD7237A/ AD7247A
reference input. References such as the AD586 5 V reference
provide the ideal external reference source for the AD7237A/
AD7247A (see Figure 9).
Op Amp Section
The output of the voltage-mode D/A converter is buffered by a
noninverting CMOS amplifier. The R
output voltage ranges to be selected. The buffer amplifier is ca-
pable of developing +10 V across a 2 k load to GND. The
output amplifier can be operated from a single +12 V to +15 V
supply by tying V
from dual supplies ( 12 V to 15 V) to allow a bipolar output
range of –5 V to +5 V. The advantages of having dual supplies
for the unipolar output ranges are faster settling time to voltages
near 0 V, full sink capability of 2.5 mA maintained over the en-
tire output range and the elimination of the effects of negative
offsets on the transfer characteristic (outlined previously). A
plot of the single supply output sink capability of the amplifier is
shown in the Typical Performance Graphs section.
INTERFACE LOGIC INFORMATION—AD7247A
Table I shows the truth table for AD7247A operation. The part
contains a single, parallel 12-bit latch for each DAC. It can be
treated as two independent DACs, each with its own CS input
and a common WR input. CSA and WR control the loading of
data to the DAC A latch while CSB and WR control the loading
of the DAC B latch. If CSA and CSB are both low, with WR
low, the same data will be written to both DAC latches. All con-
trol signals are level triggered and therefore either or both
latches can be made transparent. Input data is latched to the re-
spective latch on the rising edge of WR. Figure 4 shows the in-
put control logic for the AD7247A, while the write cycle timing
diagram for the part is shown in Figure 5.
Figure 5. AD7247A Write Cycle Timing Diagram
Figure 4. AD7247A Input Control Logic
SS
= 0 V. The amplifier can also be operated
OFS
input allows different
REV. 0