AD623ARM-REEL7 Analog Devices Inc, AD623ARM-REEL7 Datasheet - Page 18
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
AD623ARM-REEL7
Manufacturer Part Number
AD623ARM-REEL7
Description
IC,Instrumentation Amplifier,SINGLE,SSOP,8PIN,PLASTIC
Manufacturer
Analog Devices Inc
Datasheet
1.AD623-EVAL.pdf
(24 pages)
Specifications of AD623ARM-REEL7
Rohs Status
RoHS non-compliant
Amplifier Type
Instrumentation
Number Of Circuits
1
Output Type
Rail-to-Rail
Slew Rate
0.3 V/µs
-3db Bandwidth
800kHz
Current - Input Bias
17nA
Voltage - Input Offset
200µV
Current - Supply
375µA
Voltage - Supply, Single/dual (±)
2.7 V ~ 12 V, ± 2.5 V ~ 6 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
8-MSOP, Micro8™, 8-uMAX, 8-uSOP,
Current - Output / Channel
-
Gain Bandwidth Product
-
Lead Free Status / RoHS Status
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AD623ARM-REEL7
Manufacturer:
AD
Quantity:
5 510
Company:
Part Number:
AD623ARM-REEL7
Manufacturer:
AD
Quantity:
5 510
AD623
The circuit in Figure 45 should be built using a PC board with a
ground plane on both sides. All component leads should be as
short as possible. Resistors R1 and R2 can be common 1% metal
film units, but Capacitors C1 and C2 need to be ±5% tolerance
devices to avoid degrading the circuit’s common-mode rejection.
Either the traditional 5% silver mica units or Panasonic ±2%
PPS film capacitors are recommended.
In many applications, shielded cables are used to minimize
noise; for best CMR over frequency, the shield should be properly
driven. Figure 46 shows an active guard driver that is configured
to improve ac common-mode rejection by bootstrapping the
capacitances of input cable shields, thus minimizing the capacitance
mismatch between the inputs.
GROUNDING
Because the AD623 output voltage is developed with respect to
the potential on the reference terminal, many grounding problems
can be solved by simply tying the REF pin to the appropriate local
100Ω
–IN
+IN
Figure 46. Common-Mode Shield Driver
AD8031
Figure 47. Optimal Grounding Practice for a Bipolar Supply Environment with Separate Analog and Digital Supplies
R
R
2
2
G
G
2
1
8
3
AD623
–V
4
S
2
3
2
3
Figure 48. Optimal Ground Practice in a Single Supply Environment
+V
7
AD623
S
AD623
5
7
7
0.1µF 0.1µF
5
5
6
4
4
REF
6
6
OUTPUT
0.1µF
ANALOG POWER SUPPLY
Rev. D | Page 18 of 24
+5V
4
3
4
POWER SUPPLY
V
V
V
V
IN1
IN2
+5V
V
IN1
1
DD
1
DD
–5V
0.1µF
0.1µF
AGND
AGND
AD7892-2
GND
AD7892-2
6
6
ground. The REF pin should, however, be tied to a low impedance
point for optimal CMR.
The use of ground planes is recommended to minimize the
impedance of ground returns (and hence the size of dc errors).
To isolate low level analog signals from a noisy digital environment,
many data acquisition components have separate analog and
digital ground returns (see Figure 47). All ground pins from
mixed signal components, such as analog-to-digital converters
(ADCs), should be returned through the high quality analog
ground plane. Maximum isolation between analog and digital is
achieved by connecting the ground planes back at the supplies.
The digital return currents from the ADC that flow in the analog
ground plane, in general, have a negligible effect on noise
performance.
If there is only a single power supply available, it must be shared
by both digital and analog circuitry. Figure 48 shows how to
minimize interference between the digital and analog circuitry.
As in the previous case, separate analog and digital ground planes
should be used (reasonably thick traces can be used as an
alternative to a digital ground plane). These ground planes
should be connected at the ground pin of the power supply.
Separate traces should be run from the power supply to the
supply pins of the digital and analog circuits. Ideally, each device
should have its own power supply trace, but these can be shared
by a number of devices, as long as a single trace is not used to
route current to both digital and analog circuitry.
GND
ADC
ADC
DGND
DGND
14
14
12
12
DIGITAL POWER SUPPLY
MICROPROCESSOR
MICROPROCESSOR
AGND
GND
AGND
0.1µF
0.1µF
+5V
V
V
DD
DD