5M1270ZT144C5N Altera, 5M1270ZT144C5N Datasheet - Page 160
![no-image](/images/manufacturer_photos/0/0/40/altera_sml.jpg)
5M1270ZT144C5N
Manufacturer Part Number
5M1270ZT144C5N
Description
ALTERA
Manufacturer
Altera
Series
MAX® Vr
Specifications of 5M1270ZT144C5N
Programmable Type
In System Programmable
Delay Time Tpd(1) Max
6.2ns
Voltage Supply - Internal
1.71 V ~ 1.89 V
Number Of Logic Elements/blocks
1270
Number Of Macrocells
980
Number Of Gates
-
Number Of I /o
114
Operating Temperature
0°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
144-LQFP
Lead Free Status / Rohs Status
Vendor undefined / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
5M1270ZT144C5N
Manufacturer:
ALTERA11
Quantity:
260
Part Number:
5M1270ZT144C5N
Manufacturer:
ALTERA/阿尔特拉
Quantity:
20 000
8–14
Boundary-Scan Test for Programmed Devices
MAX V Device Handbook
f
levels, the devices can interface with each other. For example, a device with 3.3-V
V
transistor-to-transistor logic (TTL)-level input for the 5.0-V V
on MAX V devices can support 1.5-, 1.8-, 2.5-, or 3.3-V input levels, depending on the
V
For more information about MultiVolt I/O support, refer to the
Architecture
You can interface the TDI and TDO lines of the JTAG pins of devices that have different
V
chain must be built such that a device with a higher V
an equal or lower V
shifter may be required only to shift the TDO level to a level acceptable to the JTAG
tester.
Figure 8–13
inserted in the chain.
Figure 8–13. JTAG Chain of Mixed Voltages
For a programmed device, the input buffers are turned off by default for I/O pins that
are set as output only in the design file. You cannot sample on the programmed device
output pins with the default boundary-scan description language (BSDL) file when
the input buffers are turned off.
For boundary-scan testing, you can set the Quartus II software to always enable the
input buffers on a programmed device so it behaves the same as an unprogrammed
device, allowing sample function on output pins in the design. This aspect can cause
slight increase in standby current as the unused input buffer is always on.
To enable the unused input buffers on a programmed device, follow these steps:
1. On the Assignments menu, click Settings.
2. Under Category, select Assembler.
3. Turn on Always Enable Input Buffers.
CCIO
CCIO
CCIO
voltage of I/O Bank 1.
can drive to a device with 5.0-V V
levels by inserting a level shifter between the devices. If possible, the JTAG
chapter.
shows the JTAG chain of mixed voltages and how a level shifter is
Tester
CCIO
TDO
TDI
Accepted by Tester
Shift TDO to Level
level. By building the JTAG chain in this manner, a level
if Necessary
Shifter
V
5.0-V
Level
CCIO
CCIO
Must be 1.8-V
Chapter 8: JTAG Boundary-Scan Testing in MAX V Devices
Tolerant
Must be 5.0-V
because 3.3 V meets the minimum V
V
V
1.5-V
3.3-V
CCIO
CCIO
Tolerant
Boundary-Scan Test for Programmed Devices
CCIO
Must be 2.5-V
Tolerant
level drives to a device with
V
Must be 3.3-V
V
V
1.8-V
2.5-V
1.8-V
CCIO
December 2010 Altera Corporation
CCIO
CCIO
Tolerant
CCIO
MAX V Device
device. JTAG pins
IH
on