G2R-1-E-AC120 Omron, G2R-1-E-AC120 Datasheet - Page 18
![RELAY PWR SPDT 16A 120VAC PCB](/photos/19/19/191964/3768210_sml.jpg)
G2R-1-E-AC120
Manufacturer Part Number
G2R-1-E-AC120
Description
RELAY PWR SPDT 16A 120VAC PCB
Manufacturer
Omron
Series
G2Rr
Datasheets
1.G2R-1A-E-DC12.pdf
(14 pages)
2.G2R-1A-E-DC12.pdf
(30 pages)
3.G2R-2-SND_DC24S.pdf
(19 pages)
4.G2R-1AE-DC24.pdf
(15 pages)
Specifications of G2R-1-E-AC120
Contact Form
SPDT (1 Form C)
Contact Rating (current)
16A
Switching Voltage
380VAC, 125VDC - Max
Turn On Voltage (max)
96 VAC
Turn Off Voltage (min)
36 VAC
Relay Type
General Purpose
Coil Type
Non Latching
Coil Current
7.5mA
Coil Voltage
120VAC
Mounting Type
Through Hole
Termination Style
PC Pin
Circuit
SPDT (1 Form C)
Contact Rating @ Voltage
16A @ 250VAC
Control On Voltage (max)
96 VAC
Control Off Voltage (min)
36 VAC
Coil Voltage Vac Nom
120V
Contact Current Max
16A
Contact Voltage Ac Nom
250V
Contact Voltage Dc Nom
30V
Coil Resistance
6500ohm
Contact Configuration
SPDT
Current, Rating
16 A
Function
Power
Number Of Pins
8
Power, Rating
4000⁄480 VA⁄W
Standards
UL, CSA, VDE, CE
Termination
Through Hole
Voltage, Control
120 VAC
Voltage, Rating
380 VAC
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
G2R-1-E-AC120
G2R1EAC120
Z3121
G2R1EAC120
Z3121
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
G2R-1-E-AC120
Manufacturer:
OMRON/欧姆龙
Quantity:
20 000
■ Mounting Position
Depending on where the relay is mounted, the function of the relay
(and the performance of the circuit which includes the relay) may be
adversely affected.
The relay may malfunction if it is mounted near a transformer or other
device that generates a large magnetic field, or much heat. Provide
an adequate distance between the relay and such devices.
Also, keep the relay away from semiconductor devices, if they are to
be mounted on the same PCB.
■ Mounting Direction
To allow a relay to operate to its full capability, adequate consider-
ation must be given to the mounting direction of the relay. Relay char-
acteristics that are considerably influenced by mounting direction are
shock resistance, life expectancy, and contact reliability.
■ Shock Resistance
Ideally, the relay must be mounted so that any shock or vibration is
applied to the relay at right angles to the operating direction of the
armature of the relay. Especially when a relay’s coil is not energized,
the shock resistance and noise immunity are significantly affected by
the mounting direction of the relay.
■ Life Expectancy
When switching a heavy load that generates arc (generally, a load
having a greater impedance than that of the relay coil), substances
spattered from the contact may accumulate in the vicinity, resulting in
degradation of the insulation resistance of the circuit. Mounting the
relay in the correct direction is also important in preventing this kind
of degradation of the insulation resistance.
■ Contact Reliability
Switching both a heavy and a minute load with a single relay contact
is not recommended. The reason for this is that the substances scat-
tered from the contact when the heavy load is switched degrade the
contact when switching the minute load. For example, when using a
multi-pole contact relay, avoid the mounting direction or terminal con-
nections in which the minute load switching contact is located below
the heavy load switching contact.
18
Correct
Incorrect
Electromechanical Relays
Technical Information
■ Mounting Interval
When mounting multiple relays side by side on a PCB, pay attention
to the following points:
When many relays are mounted side by side, they may generate an
abnormally high heat due to the thermal interference between the
relays. Therefore, provide an adequate distance between the relays
to dissipate the heat. When using a relay, be sure to check the mini-
mum mounting interval.
Also, if multiple PCBs with relays are mounted to a rack, the temper-
ature may rise. In this case, preventive measures must be taken so
that the ambient temperature falls within the rated value.
Pattern Layout
Countermeasures Against Noise
The relay can be a noise source when viewed from a semiconductor
circuit. This must be taken into consideration when designing the lay-
out positioning of the relay and other semiconductor components on
the PCB.
• Keep the relay away from semiconductor components as far away
• Locate the surge suppressor for the relay coil as close to the relay
• Do not route wiring for signals such as audio signals that are likely
• Design the shortest possible pattern.
• One method for separating the power source and relay from other
■ Conformal Coating
Coating the PCB is recommended to prevent the circuitry from being
degraded by harmful gases. When coating the PCB, care should be
taken to avoid relay contamination. Otherwise, faulty contact of the
relay may occur due to sticking or coating. Some coating agents may
degrade or adversely affect the relay. Select the coating agent care-
fully.
Epoxy
Urethane
Silicon
as possible.
as possible.
to be affected by noise below the relay.
electronic components is to use shielded patterns.
* Satisfactory for sealed, but totally unsatisfactory for un-
Item
sealed relays.
PCB with relays
Good
Good
Poor *
Applicability to
mounted
Type of Coating
Good insulation. Applying this coat-
ing is a little difficult, but has no effect
on relay contact.
Good insulation and easy to coat. Be
careful not to allow the coating on the
relay itself, as thinner-based solvents
are often used with this coating.
Good insulation and easy to coat.
However, silicon gas may cause con-
tact contamination and misoperation.
Feature