G2R-1A-E-T130 DC24 Omron, G2R-1A-E-T130 DC24 Datasheet - Page 2

• Manufacturer Part Number: G2R-1A-E-T130 DC24
• Description: RELAY PWR SPST 16A 24VDC PCB
• Manufacturer: Omron
• Series: G2Rr

Specifications of G2R-1A-E-T130 DC24

• Contact Form: SPST-NO (1 Form A)
• Contact Rating (current): 16A
• Switching Voltage: 380VAC, 125VDC - Max
• Turn On Voltage (max): 16.8 VDC
• Turn Off Voltage (min): 3.6 VDC
• Relay Type: General Purpose
• Coil Type: Non Latching
• Coil Current: 21.8mA
• Coil Voltage: 24VDC
• Mounting Type: Through Hole
• Termination Style: PC Pin
• Circuit: SPST-NO (1 Form A)
• Contact Rating @ Voltage: 16A @ 250VAC
• Control On Voltage (max): 16.8 VDC
• Control Off Voltage (min): 3.6 VDC
• Coil Voltage Vdc Nom: 24V
• Contact Current Max: 16A
• Contact Voltage Ac Nom: 250V
• Contact Voltage Dc Nom: 30V
• Coil Resistance: 1100ohm
• Contact Configuration: SPST-NO
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: G2R-1A-E-T130-DC24; G2R-1A-E-T130DC24; G2R-1A-E-T130DC24; G2R1AET130DC24; Z3123

Construction
■ SEALING
Unsealed
Relays of this type are intended for manual soldering. No measures
are taken against penetration of flux and cleaning solvent into the
relay. This type of relay cannot be immersion-cleaned.
Semi-Sealed
Special design construction prevents flux from penetrating into the
relay housing, for example, due to capillary action up the terminals
when the relay is soldered onto a PCB. This type of relay also cannot
be immersion-cleaned.
2
Construction
Features
Automatic flux
application
Automatic soldering
Automatic cleaning
Manual soldering
Penetration of dust
Penetration of corrosive
gas
Construction
Features
Automatic flux
application
Automatic soldering
Automatic cleaning
Manual soldering
Penetration of dust
Penetration of corrosive
gas
Classification
Classification
Electromechanical Relays
Terminals are separated
from PCB surface when re-
lay is mounted.
Poor
Poor
Poor
Good
Fair
Poor
Terminals, base, and case are sealed.
Good
Good
Good
Good
Good
Fair
Terminals separated
from PCB
Press-fit terminals
Technical Information
Fully Sealed
Unsealed
Contacts are positioned
away from base.
Poor
Poor
Poor
Good
Resin seal
Contacts located at
upper part of relay case
Fully Sealed
Fully sealing prevents not only flux, but also cleaning solvent from
penetrating into the relay housing. Therefore, this type of relay can
be immersion-cleaned. Relays are each tested before being shipped.
The relay is immersed in fluorocarbon solution for 1 minute, at a tem-
perature of 70°C +5°C/-0°C, to see if gases escape from the relay.
The following figure illustrates the test conditions.
Terminals are pressed into
base.
Good
Good
Poor
Good
Fair
Poor
Terminal and base, as well as the base and casing, are
sealed.
Good
Good
Good
Good
Good
Fair
Terminals
separated
from PCB
Press-fit terminals
50 mm
Fluorocarbon
solution
Resin seal
Relay
Resin seal
Surface Mounting
Semi-Sealed
Terminals are inserted into
base 0.3 mm min. thick.
Good
Good
Poor
Good
Terminals
separated
from PCB
Ex.) 70 °C
Glue pad
Inserted terminals
0.3 mm
min. base
thickness