HEDS-6500#B12 Avago Technologies US Inc., HEDS-6500#B12 Datasheet
HEDS-6500#B12
Specifications of HEDS-6500#B12
Related parts for HEDS-6500#B12
HEDS-6500#B12 Summary of contents
Page 1
... Features • Two channel quadrature output with optional index pulse • TTL compatible single ended outputs on HEDS Series • 100ºC operating temperature for metal code wheel • 70°C operating temperature for mylar code wheel • Industry standard AM26C31Q CMOS line driver IC on HEDL Series • ...
Page 2
... HEDL-65XX fig 2 25.91 ∅ (1.020) 2.44 ∅ (0.096) 0.254 SLOTTED (0.010) 13.2 ∅ (0.52) HEDL-54XX fig 3 65.9 (2.59) HEDS-65XX #xxx YYMM COUNTRY OF ORIGIN 24.9 (0.98) 30.2 (1.19) HEDL-65XX fig 4 24.0 ± 0.5 (192.2) 55.88 ∅ (2.200) 24.38 (0.960) 2.44 ∅ (0.096) 17 ...
Page 3
... PHOTO DIODES LENS LED SIGNAL PROCESSING CIRCUITRY EMITTER CODE SECTION WHEEL There are two different connector pin-out configurations used with the HEDS-65xx / HEDL-65xx series of encoders. The table below relates the part to its connector pin-out. Connector Pin-out 3 COMPARATORS INDEX-PROCESSING CIRCUITRY DETECTOR SECTION COMPARATORS ...
Page 4
... B. Due to this integrated phasing technique, the digital output of channel quadrature with that of channel B (90 degrees out of phase). In the HEDS-6540 / HEDL-6540 the output of the com- parator for the index pulse is combined with that of the outputs of channel A and channel B to produce the final index pulse ...
Page 5
Output Waveforms OUTPUT PHASE OUTPUT CH I OUTPUT Waveforms for Encoders without Line Drivers Waveforms for Encoders with Line Drivers. HEDL-65XX fig ...
Page 6
... Shaft Eccentricity Plus Radial Play Note: The HEDS-65XX performance is guaranteed to 100 kHz but can operate at higher frequencies. For frequencies above 100 kHz it is recommended that the load capacitance not exceed 25 pF and pull up resistors of 3.3 kΩ between the output channels and Vcc are included ...
Page 7
... Cycle Error Index Pulse Width *Typical values specified at Vcc = 5.0 V and 25°C. **HEDS-6540 – Active high Index part. Pull-up of 2.7 kΩ used on all outputs of modules that do not have a line driver. ***HEDS-6500 – 3.3 kΩ pull-up resistors used on all encoder module outputs. 7 Symbol Min ...
Page 8
... High Level Output Voltage Electrical Interfaces To insure reliable encoding performance, the HEDS-6540 three channel encoder requires 2.7 kΩ pull-up resistors to the supply voltage on each of the three output lines Ch. A, Ch. B, and Ch. I located as close as possible to the encoder Mechanical Characteristics Parameter ...
Page 9
... CHAMFER 2 PLACES If neither locating pins nor locating boss are available, then a centering tool supplied by Avago can be used (HEDS- 6510). The following figure shows how the main encoder components are organized. Encoder Mounting and Assembly 9 24.38 (0.960) ∅ ...
Page 10
ALIGNMENT TOOL ASSEMBLE COMPONENTS AND MOUNTING SCREWS AND TOOLS AS APPROPRIATE. 2 LOAD ENCODER BASEPLATE ONTO RECEIVING SURFACE (MOTOR END PLATE) WITH MOUNTING SCREW HOLES ALIGNED WITH MATING HOLES. LOAD MOUNTING SCREWS AND LEAVE SLIGHTLY LOOSE. 10 HEDL-65XX fig ...
Page 11
CHOOSE CENTERING CYLINDER OR UNDERSIDE LOCATING PINS. CENTERING CYLINDER: LOCATE ENCODER BASEPLATE WITH CENTERING CYLINDER. WHEN IN PLACE, TIGHTEN MOUNTING SCREWS. LOCATING PINS: WITH LOCATING PINS PROPERLY SEATED IN CORRESPONDING RECEIVING HOLES IN ENCODER BASEPLATE, TIGHTEN MOUNTING SCREWS. 4 ...
Page 12
ALLEN WRENCH TO TIGHTEN CODEWHEEL SET SCREW CODEWHEEL GAPPING TOOL WITH CODEWHEEL AND ENCODER MODULE IN PLACE, PLACE CODEWHEEL GAPPING TOOL UNDER CODEWHEEL AS SHOWN. INSERT THE ALLEN WRENCH INTO THE CODEWHEEL SET SCREW AND TIGHTEN. REMOVE ...
Page 13
... Ordering Information for 2CH and 3CH Encoder Modules Encoders Metal Codewheel (up to 100°C) HEDS - 65 OUTPUTS THROUGH HOLE 0 – – None 4 – – 13.3 mm (0.525 in.) 05 HEDS-6500 HEDS-6505 HEDS-6540 HEDS-6545 Encoders Film Codewheel (up to 70°C) HEDM – 65 THROUGH HOLE OUTPUTS 0 – None 0 – ...
Page 14
... OUTPUTS THROUGH HOLE 0 – – None 4 – – 13.3 mm (0.525 in HEDL-6540# B HEDL-6545 Ordering Information for HEDS=76XX Centering Tools HEDS-6510 Option 0 SHAFT DIAMETER 05 – 3/16 in. 06 – 1/4 in. 08 – 3/8 in. 09 – 1/2 in HEDS-6510 Ordering Information for HEDS-65XX Codewheel Gapping Tool ...