MAX11008EVKIT+ Maxim Integrated Products, MAX11008EVKIT+ Datasheet - Page 2

• Manufacturer Part Number: MAX11008EVKIT+
• Description: Power Management Modules & Development Tools KIT EVAL MAX11008 BIAS CTLR
• Manufacturer: Maxim Integrated Products

Specifications of MAX11008EVKIT+

• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

MAX11008 Evaluation Kit/
Evaluation System
Note: Indicate you are using the MAX11008 when contacting these component suppliers.
•
•
•
•
•
Note: In the following sections, software-related items
are identified by bolding. Text in bold refers to items
directly from the EV kit software. Text in bold and under-
lined refers to items from the Windows operating system.
The MAX11008 EV kit is fully assembled and tested.
Follow the steps below to verify board operation. Caution:
Do not turn on the power until all connections are
completed.
1) Ensure that the MAX11008EVKIT jumpers are set in
2
Fairchild Semiconductor
International Rectifier
TDK Corp.
Vishay
DESIGNATION QTY
R10, R11
R12, R13
R14, R15
_______________________________________________________________________________________
Maxim MAX11008EVC16 (contains MAX11008EVKIT+
board, HSI2CMOD, and 68HC16MODULE-DIP)
DC power supply, 8V at 500mA
DC power supply, 10V at 1000mA
Windows 98/2000/XP computer with a spare serial
(COM) port
9-pin I/O extension cable
accordance with Table 1.
R5, R6
R7, R8
R4
U1
SUPPLIER
1
2
2
2
2
2
1
0Ω resistor (0603)
1.00Ω ±1% sense resistors (2010)
Vishay (Dale) CRCW20101R00FNEF
Dual RF LDMOS CODEC
(48 TQFN-EP*)
Maxim 11008BETM+
100Ω ±5% resistors (1206)
0Ω resistors (1206)
10kΩ ±5% resistors (1206)
47Ω ±5% resistors (1206)
Required Equipment
DESCRIPTION
Quick Start
Procedure
888-522-5372
310-322-3331
847-803-6100
402-563-6866
PHONE
MAX11008EVKIT Component List (continued)
* EP = Exposed pad.
2) Carefully connect the boards by aligning the 40-pin
3) Connect the 8V DC power source to the
4) Connect a cable from the computer’s serial port to
5) Install the evaluation software on your computer by
DESIGNATION QTY
header of the HSI2CMOD with the 40-pin connector of
the 68HC16MODULE-DIP module. Gently press them
together. The two boards should be flush against one
another. Next, connect the MAX11008 EVKIT 20-pin
connector to the HSI2CMOD board.
68HC16MODULE at the terminal block located next
to the on/off switch, along the top edge of the mod-
ule. Observe the polarity marked on the board.
the 68HC16MODULE. If using a 9-pin serial port,
use a straight-through, 9-pin female-to-male cable.
If the only available serial port uses a 25-pin con-
nector, a standard 25-pin to 9-pin adapter is
required. The EV kit software checks the modem
status lines (CTS, DSR, DCD) to confirm that the
correct port has been selected.
launching MAX11008.msi. (The latest software can
be found at www.maxim-ic.com/evkitsoftware.)
The program files are copied and icons are created
for them in the Windows Start menu.
U2
U3
—
—
Component List (continued)
www.fairchildsemi.com
www.irf.com
www.component.tdk.com
www.vishay.com
21
1
1
1
Component Suppliers
2.5V voltage reference (8 SO)
Maxim MAX6126AASA25+
28V input linear regulator (5 SOT23)
Maxim MAX1615EUK+T
(Top Mark: ABZD)
Shunts
PCB: MAX11008 Evaluation Kit+
WEBSITE
DESCRIPTION