Features
PEX 8619 General Features
o 16-lane PCI Express switch
o Up to 16 configurable ports
o 19 x 19mm
o Typical Power: 1.99 Watts
PEX 8619 Key Features
o Standards Compliant
o Integrated DMA Engine
o High Performance
o Dual-Host & Fail-Over Support
o Flexible Configuration
o PCI Express Power Management
o Spread Spectrum Clock Isolation
o Quality of Service (QoS)
o Reliability, Availability, Serviceability
- Integrated 5.0 GT/s SerDes
- PCI Express Base Specification r2.0
- PCI Power Management Spec r1.2
- Microsoft Vista Compliant
- Supports Access Control Services
- Dynamic link-width control
- Four DMA Channels
- Internal Descriptor Support
- DMA function independent from
- 64-bit Addressing
- Prefetch Descriptor Mode
- Up to 4.0 GB/s throughput per channel
- Cut-Thru latency: 140ns
- 2KB max payload size
- Read Pacing
- Dual-Cast
- Configurable Non-Transparent port
- Moveable upstream port
- Crosslink port capability
- 16 flexible & configurable ports
- Configurable with strapping pins,
- Lane and polarity reversal
- Link power management states: L0, L0s,
- Device states: D0 and D3
- Dual clock domain
- Two Virtual Channels (VC) per port
- Eight Traffic Classes per port
- Weighted Round-Robin Port & VC
- All ports Hot-Plug capable thru I
- Data path protection
- Memory (RAM) error correction
- Port Status bits and GPIO available
- Per port error diagnostics
- Performance monitoring
(Backwards compatible with PCIe
r1.0a/1.1)
transparent switch function
(NTB)
(x1, x4, or x8)
EEPROM, I
L1, L2/L3 Ready, and L3
Arbitration
(Hot-Plug Controller on every port)
(per port payload & header counters)
Version 1.4 2010
2
, 324-ball HSBGA
2
C, or Host software
hot
2
C
The ExpressLane
enabling users to add scalable high bandwidth non-blocking interconnection to a
wide variety of applications including control planes, communication platforms,
servers, storage systems and embedded systems. The PEX 8619 is well suited for
fan-out, aggregation, peer-to-peer, and intelligent I/O module applications
Low Packet Latency & High Performance
The PEX 8619 architecture supports packet cut-thru with a maximum latency of
140ns. This, combined with large packet memory and non-blocking internal switch
architecture, provides full line rate on all ports for low-latency applications such as
communications and servers. The low latency enables applications to achieve high
throughput and performance. In addition to low latency, the device supports a max
payload size of 2048 bytes, enabling the user to achieve even higher throughout
Integrated DMA Engine
The PEX 8619 provides a versatile and powerful DMA engine built in to the device
which can be used as a stand alone DMA engine. The DMA engine removes the
burden resulting from having to move data between devices away from the
processor. This allows the processor to perform computational tasks instead. The
four DMA channels can support high data rate transfers between IO devices
connected to any of the available ports in the PEX8619. Additionally, the DMA
engine in the PEX 8619 can be used to complement the DMA engine in the
processor by providing additional DMA channels for higher performance.
Data Integrity
The PEX 8619 provides end-to-end CRC protection (ECRC) and Poison bit support
to enable designs that require guaranteed error-free packets. PLX also supports
data path parity and memory (RAM) error correction as packets pass through the
switch
Dual-Host and Fail-Over Support
The PEX 8619 supports full non-transparent bridging (NTB) functionality to allow
implementation of multi-host systems and intelligent I/O modules in applications
which require redundancy support such as communications, storage, and servers.
Non-transparent bridges allow systems to isolate host memory domains by
presenting the processor subsystem as an endpoint rather than another memory
system. Base address registers are used to translate addresses; doorbell registers are
used to send interrupts between the address domains; and scratchpad registers are
accessible from both address domains to allow inter-processor communication
Interoperability
The PEX 8619 is designed to be fully compliant with the PCI Express Base
Specification r2.0 and is backwards compatible to PCI Express Base Specification
r1.1 and r1.0a. Additionally each port supports auto-negotiation, lane reversal and
polarity reversal. Furthermore, the PEX 8619 is designed for Microsoft Vista
compliance. All PLX switches undergo thorough interoperability testing in PLX’s
Interoperability Lab and compliance testing at the PCI-SIG plug-fest to ensure
compatibility with PCI Express devices in the market.
Flexible & Versatile 16-lane 16-port PCI Express
.
PEX 8619
™
PEX 8619 device offers PCI Express switching capability
®
Switch
.
.
.