31-70008-1000 Amphenol, 31-70008-1000 Datasheet
31-70008-1000
Specifications of 31-70008-1000
Related parts for 31-70008-1000
31-70008-1000 Summary of contents
Page 1
... Slide outer ferrule over braid and up against connector body. Crimp outer ferrule using Die Set Cavity specified in table above. 279 Amphenol ® Stripping Dimensions, inches (mm .437(11.1) .312(7.9) .248(6.3) .125(3.2) .437(11.1) .312(7.9) .248(6.3) .125(3.2) .437(11.1) .312(7.9) .248(6.3) .125(3.2) www.amphenolrf.com ...
Page 2
... Not supplied on all items Step 1 a Step 2 Step 3 Step 4 Step 5 For angle plugs only: (except 31-204) Solder center conductor to preassembled contact. Assemble cap and lightly punch center of cap for retention in body, or solder in place. Amphenol Corporation Tel: 800-627-7100 clamp bushing‡ female contact jack body ‡ ...
Page 3
... Slide outer ferrule onto cable as shown. For RG-174, 179, 187, 188, 316/U cables only, slit jacket back .100"(2.5mm) as shown. Before attaching center contact, slide metal spacer/TFE sleeve (not shown) over cable dielectric and under braid. The center contact should butt against the dielectric and TFE sleeve ...
Page 4
... Step For RG-174, 179, 187, 188, 316/U cables only, slit jacket back .100"(2.5mm) as shown. Before attaching center contact, slide metal spacer/TFE sleeve (not shown) over cable dielectric and under braid. The center contact should butt against the dielectric and TFE sleeve. ...
Page 5
... Cable Number Type RG-/U 31-351 BNC Plug 58, 141 31-359 BNC Plug 59, 62, 140 31-371 BNC Plug 174, 179, 187, 188, 316 boot Step 1 outer ferrule Step 2 Step 3 outer ferrule must Step 4 clamp nut assy as shown Step 5 note: center conductor must be visible thru contact solder ...
Page 6
... BNC Plug 59 31-5137 BNC Plug 58 31-5137-RFX BNC Plug 58 Step 1 Strip cable as shown. Take care not to nick center conductor or outer braid. Step 2 Twist outer braid in a clockwise direction so that at least min. of cable 1/32" of cable dielectric is bared, and braid is left flat. (Stray dielectric or loose braid can cause shorts ...
Page 7
... Slide clamp nut over cable. Strip cable to dimension shown. Cut braid and dielectric square. Do not nick center conductor. Step 1B For 31-4541-RFX.. Same as step 1A except use Step 1B strip dimensions, and then slit jacket back .125"(3.2 mm) in four places 90° apart as shown in illustration. ...
Page 8
... Connector Cable Number Type RG-/U 31-4700 BNC Plug 58, 141 31-4702 BNC Plug 59 .250(6.4) .156(4.0) Step 1 Slide ferrule over cable end, slotted end first. Strip cable to dimensions shown. Do not nick center conductor. Flare braid slightly as shown. Step 2 Tin exposed center conductor. Solder center contact on center conductor ...
Page 9
... Hex Crimp Data Amphenol Connector Cable Number Type 31-70000 75 BNC Plug 6, Belden 9248, Plenum 6 31-70000-1000 75 BNC Plug 6, Belden 9248 31-70008 75 BNC Plug 59 31-70008-1000 75 BNC Plug 59 (20GA CC) 31-70008-3000 75 BNC Plug 59 (.032 CC) 31-70009 75 BNC Jack 59 31-70013 75 BNC Plug 179, 187 31-70013-1000 ...
Page 10
... BNC Plug Quad Shield 59 Step 1 For RG-174, 179, 187, 188, 316/U cables only, slit jacket back .100"(2.5mm) as shown. Before attaching center contact TFE sleeve (not shown) over cable dielectric and under braid. For 31-71016, before attaching center contact. Slide metal spacer/TFE sleeve (not shown) over cable dielectric and under braid ...