5223008-4 TE Connectivity, 5223008-4 Datasheet - Page 6

• Manufacturer Part Number: 5223008-4
• Description: HARD METRIC CONNECTOR, RECEPTACLE 120POS
• Manufacturer: TE Connectivity
• Type: Backplaner
• Series: Z-PACKr

Specifications of 5223008-4

• Pitch (mm): 2mm
• Gender: RCP
• Body Orientation: Right Angle
• Number Of Contact Rows: 5
• Number Of Contacts: 120POS
• Termination Method: Press Fit
• Mounting Style: Through Hole
• Contact Plating: Gold Over Nickel
• Voltage Rating Max: 30VAC
• Current Rating (max): 3/ContactA
• Operating Temp Range: -55C to 125C
• Contact Material: Phosphor Bronze
• Housing Color: Natural
• Housing Material: Liquid Cryst Polymer
• Product Height (mm): 13.8mm
• Product Depth (mm): 22.45mm
• Product Length (mm): 47.88mm
• Connector Type: Backplane
• Row Pitch: 2mm
• Pitch Spacing: 2mm
• No. Of Contacts: 120
• Contact Termination: Press Fit
• No. Of Rows: 5
• Rohs Compliant: Yes
• Number Of Rows: 5
• Number Of Positions / Contacts: 120
• Mounting Angle: Right
• Pitch: 2 mm
• Termination Style: Solder Pin
• Product Type: Connector
• Pcb Mounting Orientation: Right Angle
• Post Type: Press-Fit
• Module Type: Signal
• Voltage Rating (vac): 30
• Termination Post Length (mm [in]): 3.56 [0.140]
• Number Of Signal Positions: 120
• Sequencing: No
• Post Plating: Tin
• Centerline, Matrix (mm [in]): 2.00 x 2.00 [.079 x .079]
• Contact Type: Socket
• Contact Base Material: Phosphor Bronze
• Contact Plating, Mating Area, Material: Gold (30)
• Connector Style: Receptacle
• Rohs/elv Compliance: RoHS compliant, ELV compliant
• Lead Free Solder Processes: Not relevant for lead free process
• Rohs/elv Compliance History: Always was RoHS compliant
• Applies To: Printed Circuit Board
• Application: Free-Board
• Lead Free Status / RoHS Status: Compliant

4.2.
4.3.
4.4.
Rev C
B.
Requalification Testing
If changes significantly affecting form, fit or function are made to the product or manufacturing process,
product assurance shall coordinate requalification testing, consisting of all or part of the original testing
sequence as determined by development/product, quality and reliability engineering.
Acceptance
Acceptance is based on verification that the product meets requirements of Figure 1. Failures attributed
to equipment, test setup or operator deficiencies shall not disqualify the product. When product failure
occurs, corrective action shall be taken and samples resubmitted for qualification. Testing to confirm
corrective action is required before resubmittal.
Quality Conformance Inspection
The applicable quality inspection plan will specify the sampling acceptable quality level to be used.
Dimensional and functional requirements shall be in accordance with the applicable product drawing
and this specification.
2.
Test Sequence
Qualification inspection shall be verified by testing samples as specified in Figure 3.
Power connectors.
Power connector housings and contacts shall be prepared in accordance with applicable
Instruction Sheets and shall be selected at random from current production. All test groups
shall consist of 5 connectors each of the largest available size. All tests requiring individual
contact measurements shall be conducted on 30 contacts randomly selected over the 5
connectors. Test groups 1 and 2 shall be mounted on printed circuit boards designed to
accommodate vibration and physical shock fixturing providing a series circuit for all contacts
with access to measure termination resistance.
Contact Resistance Measurement Points
Figure 4
108-1441
6 of 8