Y40695K00000J0L Vishay, Y40695K00000J0L Datasheet - Page 3

• Manufacturer Part Number: Y40695K00000J0L
• Manufacturer: Vishay
• Type: Trimmerr

Specifications of Y40695K00000J0L

• Resistance: 5kohm
• Power Rating: 1/4W
• Tolerance (+ Or -): 5%
• Number Of Turns: 21Turn
• Technology: Metal Foil
• Mounting Style: Through Hole
• Termination Style: Pin
• Operating Temp Range: -55C to 150C
• Military Standard: MIL-PRF-39035
• Shaft Diameter (mm): 2.29mm
• Product Diameter (mm): Not Requiredmm
• Product Depth (mm): 4.32mm
• Lead Free Status / RoHS Status: Not Compliant

Notes
(1)
(2)
(3)
(4)
(5)
Document Number: 63054
Revision: 24-Mar-10
TABLE 5 - COMPARISON
TEST GROUP I
Conditioning
Contact resistance variation - CRV (noise)
Immersion
TEST GROUP Ia
Visual and mechanical
Actual effective electrical travel
End resistance
Dielectric withstanding voltage - DWV
Per MIL-STD-202, methods 301 and 105
Atmospheric pressure
Barometric pressure
Insulation resistance
Shaft torque
Thermal shock
Setting stability
TEST GROUP II
Solderability
TEST GROUP III
Resistance temperature characteristic - TCR
Moisture resistance
Contact resistance variation - CRV (noise)
TEST GROUP IV
Settability
Shock
Setting stability
Vibration
Setting stability
Contact resistance variation - CRV (noise)
Salt spray
TEST GROUP V
Solder heat
Low-temperature operation
Setting stability
Low-temperature storage
High-temperature exposure
Setting stability
Contact resistance variation - CRV (noise)
Integrity of shaft
TEST GROUP VI
Rotational life (200 cycles)
Contact resistance variation - CRV (noise)
Terminal strength
TEST GROUP VII
Life (2000 h) at + 85 °C
Life (10 000 h) at + 85 °C
TEST GROUP VIII
Solvent resistance
Maximum TCR applies to the 3 σ (sigma) limit or 99.73 % of a
production lot. (Measured end-to-end with wiper off the element.)
Measurements of TCR through the wiper are influenced more by
setting stability and the percentage of the total resistance in use
(at the wiper) than by fundamental resistance change due to
temperature alone. The parameter shown in table 2 is a 2 s
distribution typifying the behavior of the device when used with
40 % or more of the total resistance in use.
Derated linearly for full power at + 85 °C to zero power at
+ 150 °C. See figure 2.
All ΔR’s are measured to the tolerance specified + 0.01 Ω.
Whichever is greater.
Special available options:
Special marking
Power conditioning and screening operations.
For any questions, contact:
MIL-PRF-39035/2 CHARACTERISTIC H
No continuous stream of bubbles
Per MIL-STD-202, method 208
± 0.005 %/°C (± 50 ppm/°C)
No loosening or breakage
3 oz. in. maximum
± 3.0 % or 3 Ω
3.0 % or 3 Ω
3.0 % or 3 Ω
3.0 % or 3 Ω
3.0 % or 3 Ω
600 V
250 V
10 to 25 turns
2 % or 2 Ω
No corrosion
≥ 1000 MΩ
No failures
No failures
± 1.0 %
± 1.0 %
± 1.0 %
± 1.0 %
± 1.0 %
± 1.0 %
± 1.0 %
± 1.0 %
± 1.0 %
± 1.0 %
± 1.0 %
± 2.0 %
± 1.0 %
± 3.0 %
± 2.0 %
± 2.0 %
± 3.0 %
± 5.0 %
2 lbs.
AC
AC
, 1 min
, 1 min
VISHAY TRIMMERS ARE INSPECTED
100 % for:
• Immersion
• Resistance tolerance check
• End resistance
• Visual-mechanical
• Dynamic tests for continuity, CRV
By sample for:
• TCR
• DWV
[e-mail]
(5)
(5)
(5)
(5)
(5)
Accutrim™ 1260 (RJ24 Style)
(5)
(4)
± 0.1 % typical, ± 1.0 % maximum
± 0.1 % typical, ± 1.0 % maximum
No continuous stream of bubbles
Per MIL-STD-202, method 208
± 0.001 %/°C (± 10 ppm/°C)
Vishay Foil Resistors
3 Ω typical, 10 Ω maximum
3 Ω typical, 10 Ω maximum
3 Ω typical, 10 Ω maximum
3 Ω typical, 10 Ω maximum
3 Ω typical, 10 Ω maximum
No loosening or breakage
2 Ω for values ≤ 1 kΩ;
5 Ω for values ≥ 2 kΩ;
3 oz. in. maximum
1260 MAXIMUM
600 V
250 V
No corrosion
21 ± 2 turns
> 1000 MΩ
No failures
No failures
± 0.5 %
± 0.5 %
± 0.5 %
± 0.5 %
± 0.1 %
± 0.5 %
± 0.5 %
± 0.5 %
± 0.5 %
± 0.1 %
± 0.5 %
± 0.5 %
± 0.5 %
± 0.5 %
± 0.5 %
± 2.0 %
2 lbs.
AC
AC
, 1 min
, 1 min
www.foilresistors.com
3