PVZ2A203A01R00 Murata, PVZ2A203A01R00 Datasheet - Page 3
![Trimmer Resistors - SMD 20K OHM SMD 2MM](/photos/16/33/163349/poz2anpt_sml.jpg)
PVZ2A203A01R00
Manufacturer Part Number
PVZ2A203A01R00
Description
Trimmer Resistors - SMD 20K OHM SMD 2MM
Manufacturer
Murata
Type
Trimmerr
Datasheet
1.PVZ2A203A01R00.pdf
(6 pages)
Specifications of PVZ2A203A01R00
Resistance
20kohm
Power Rating
1/10W
Tolerance (+ Or -)
30%
Number Of Turns
1Turn
Technology
Carbon Film
Mounting Style
Surface Mount
Termination Style
J-Hook
Failure Rate
Not Required
Shaft Diameter (mm)
2.2mm
Product Diameter (mm)
Not Requiredmm
Product Length (mm)
2.1mm
Product Height (mm)
2mm
Product Depth (mm)
2.7mm
Temperature Coefficient
±500
Tolerance
30 %
Operating Temperature Range
- 25 C to + 85 C
Element Type
Carbon
Product
Single-Turn Trimmer Potentiometers
Taper
Linear
Lead Free Status / RoHS Status
Compliant
!Note
!Note
1. Store in temperatures of -10 to +40 deg. C and
2. Do not store in or near corrosive gases.
3. Use within six months after delivery.
4. Open the package just before using.
5. Do not store under direct sunlight.
6. If you use the trimmer potentiometer in an
1. When using with partial load (rheostat), minimize
2. The maximum input voltage to a trimmer
3. The maximum input current to a trimmer
4. If the trimmer potentiometer is used in DC and high
1. Soldering
(1) Reflow soldering and Soldering Iron are
(2) Use our standard land dimension. Excessive land
(3) Standard soldering condition
(4) Apply the appropriate amount of solder paste.
the power depending on the resistance value.
potentiometer should not exceed (P.R)^1/2 or the
maximum operating voltage, whichever is smaller.
potentiometer should not exceed (P/R)^1/2 or the
allowable wiper current, whichever is smaller.
humidity conditions, please connect wiper (#2) for
plus and resistive element (#1 or #3) for minus.
Notice (Operating and Storage Conditions)
relative humidity of 30-85%RH.
environment other than listed below, please
consult with a Murata factory representative prior
to using.
The trimmer potentiometer should not be used under
Notice (Rating)
Notice (Soldering and Mounting)
(a) Reflow soldering :
(b) Soldering iron:
available. Cannot be soldered using the flow
soldering method. If you use the flow soldering
method, the trimmer potentiometer may not
function.
area causes displacement due to the effect of the
surface tension of the solder. Insufficient
land area leads to insufficient soldering
strength of the chip.
Before using other soldering conditions than
those listed above, please consult with Murata
factory representative prior to using. If the
soldering conditions are not suitable, e.g.,
excessive time and/or excessive temperature, the
trimmer potentiometer may deviate from the
specified characteristics.
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
>Temperature of tip 360 deg. C max.
>Soldering time
>Diameter
>Wattage of iron
Refer to the standard temperature profile.
30W max.
1mm max.
3 sec. max.
2. Mounting
3. Cleaning
(1) Corrosive gaseous atmosphere
(2) In liquid
(3) Dusty / dirty atmosphere
(4) Direct sunlight
(5) Static voltage nor electric/magnetic fields
(6) Direct sea breeze
(7) Other variations of the above
(5) The soldering iron should not come in contact
(1) Do not apply excessive force (preferably 4.9N
(2) Do not warp and/or bend PC board to prevent
(3) In chip placers, the recommended size of the
(1) In case there is flux on the resistive element,
(2) Isopropyl-alcohol and Ethyl-alcohol are
the following environmental conditions:
(Ex. Chlorine gas, Hydrogen sulfide gas, Ammonia
gas, Sulfuric acid gas, Nitric oxide gas, etc.)
(Ex. Oil, Medical liquid, Organic solvent, etc.)
The thickness of solder paste should be printed
from 100 micro m to 150 micro m and the
dimension of land pattern used should be Murata's
standard land pattern at reflow soldering.
Insufficient amounts of solder can lead to
insufficient soldering strength on PCB.
Excessive amounts of solder may cause bridging
between the terminals.
with the case of the trimmer potentiometer. If
such contact does occur, the trimmer
potentiometer may be damaged.
(Ref.; 500gf) max.), when the trimmer
potentiometer is mounted to the PCB.
trimmer potentiometer from breakage.
cylindrical pick-up nozzle should be outer
dimension 1.5-1.8mm dia. and inner dimension
1.3mm dia.
clean sufficiently with cleaning solvents and
completely remove all residual flux.
PVZ2 Series Notice
Continued on the following page.
R50E13.pdf 04.6.11
7
1