PV32H102A01B00 Murata, PV32H102A01B00 Datasheet - Page 38
![Trimmer Resistors - Single Turn 1K OHM 6MM SGL TRN](/photos/16/51/165148/131p01_sml.jpg)
PV32H102A01B00
Manufacturer Part Number
PV32H102A01B00
Description
Trimmer Resistors - Single Turn 1K OHM 6MM SGL TRN
Manufacturer
Murata
Type
Trimmerr
Datasheet
1.PV32H102A01B00.pdf
(59 pages)
Specifications of PV32H102A01B00
Resistance
1kohm
Power Rating
1/2W
Tolerance (+ Or -)
20%
Number Of Turns
1Turn
Technology
Cermet
Mounting Style
Through Hole
Termination Style
Pin
Operating Temp Range
-55C to 125C
Failure Rate
Not Required
Shaft Diameter (mm)
2.8mm
Product Diameter (mm)
6.6mm
Product Length (mm)
Not Requiredmm
Product Height (mm)
4.95mm
Product Depth (mm)
Not Requiredmm
Temperature Coefficient
±100
Tolerance
20 %
Operating Temperature Range
- 55 C to + 125 C
Product
Trimmer Resistors - Single Turn
Taper
Linear
Lead Free Status / RoHS Status
Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PV32H102A01B00
Manufacturer:
MURATA
Quantity:
240 000
7
!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
Soldering profile for Lead-free solder (96.5Sn/3.0Ag/0.5Cu), Eutectic solder (63Sn/37Pb)
1. Use suitable screwdrivers that fit comfortably in
2. Do not apply more than 9.8N (Ref. 1kgf) of twist
1. Please make sure that your product has been
2. Murata cannot guarantee trimmer potentiometer
36
PV32 Series Notice
PV32
PV32
Series
Series
Soldering Profile
Notice (Handling)
driver slot. We recommend the screwdrivers below.
* Recommended screwdriver for manual adjustment
We can supply the screwdrivers above.
If you place an order, please specify the
Murata P/N.
and stress after mounting onto PCB to prevent
contact intermittence. If excessive force is
applied, the trimmer potentiometer may not
function.
Notice (Other)
evaluated and confirmed against your
specifications when our product is mounted to your
product.
integrity when used under conditions other than
those specified in this document.
Flow Soldering Profile
Soldering Iron
<PV32 series>
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
ENGINEER INC.: DA-40
(Murata P/N: KMDR180)
Temperature of Soldering Iron Tip
Temp. (T1)
T1
150
C
Pre-heating
Pre-heating
350 10
t1
60 to 120
Time (t1)
C
T3
T2
sec.
Heating
t2
Standard Profile
Temp. (T2)
Time (s)
250
C
Heating
Limit Profile
Standard Profile
Soldering Time
Time (t2)
5 max.
sec.
3 max.
sec.
of Flow
Cycle
Standard Condition
Time
1
3. When adjusting with an adjustment tool, the applied
4. The rotational torque at the position of the
5. When using a lock paint to fix slot position,
force to the adjustment screw should not exceed
4.9N (Ref. 500gf). If excessive force is applied,
the trimmer potentiometer may not function due to
damage.
adjustment range should not exceed the stop
strength.
please use adhesive resin without chlorine or
sulfur (Three-bond "1401 series") and evaluate
performance with your product. Lock paint may
cause corrosion or electrical contact problems.
Temp. (T1)
Soldering Iron Power Output
150
C
Pre-heating
30 max.
W
60 to 120
Time (t1)
sec.
Limit Profile
Temp. (T3)
260
C
Heating
Cycle of Soldering Iron
Time (t2)
3 max.
sec.
Time
1
of Flow
Cycle
Time
1
R50E.pdf
08.8.26