PVZ3A503A01R00 Murata, PVZ3A503A01R00 Datasheet - Page 49
![Trimmer Resistors - SMD 50K OHM SMD 3MM](/photos/16/51/165154/130p01_sml.jpg)
PVZ3A503A01R00
Manufacturer Part Number
PVZ3A503A01R00
Description
Trimmer Resistors - SMD 50K OHM SMD 3MM
Manufacturer
Murata
Type
Trimmerr
Series
PVZ3Ar
Datasheet
1.PVZ3A503A01R00.pdf
(59 pages)
Specifications of PVZ3A503A01R00
Resistance
50kohm
Power Rating
1/10W
Tolerance (+ Or -)
30%
Number Of Turns
1Turn
Technology
Carbon Film
Mounting Style
Surface Mount
Termination Style
J-Hook
Operating Temp Range
-25C to 85C
Failure Rate
Not Required
Shaft Diameter (mm)
3mm
Product Diameter (mm)
Not Requiredmm
Product Length (mm)
3.1mm
Product Height (mm)
1.85mm
Product Depth (mm)
3.6mm
Temperature Coefficient
±500
Tolerance
30 %
Operating Temperature Range
- 25 C to + 85 C
Element Type
Carbon
Product
Single-Turn Trimmer Potentiometers
Taper
Linear
Lead Free Status / RoHS Status
Compliant
!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
Soldering profile for Lead-free solder (96.5Sn/3.0Ag/0.5Cu), Eutectic solder (63Sn/37Pb)
1. Use suitable screwdrivers that fit comfortably in
2. Do not apply more than 9.8N (Ref. 1kgf) of twist
1. Please make sure that your product has been
2. Murata cannot guarantee trimmer potentiometer
PV12
PV37
PV36
PV12
PV37
PV36
Series
Series
Soldering Profile
Notice (Handling)
driver slot. We recommend the screwdrivers below.
* Recommended screwdriver for manual adjustment
We can supply the screwdrivers above.
If you place order, please specify the Murata P/N.
and stress after mounting onto PCB to prevent
contact intermittence. If excessive force is
applied, the trimmer potentiometer may not
function.
Notice (Other)
evaluated and confirmed against your
specifications when our product is mounted to your
product.
integrity when used under conditions other than
those specified in this document.
Flow Soldering Profile
Soldering Iron
ENGINEER INC.: DA-40
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
(Murata P/N: KMDR180)
Temperature of Soldering Iron Tip
Temp. (T1)
T1
150
C
Pre-heating
Pre-heating
350 10
t1
60 to 120
Time (t1)
C
T3
T2
sec.
Heating
t2
Standard Profile
Temp. (T2)
Time (s)
250
C
Heating
Limit Profile
Standard Profile
Soldering Time
Time (t2)
5 max.
sec.
3 max.
sec.
of Flow
Cycle
Standard Condition
Time
1
3. When adjusting with an adjustment tool, the applied
4. When using a lock paint to fix slot position,
force to the adjustment screw should not exceed
4.9N (Ref. 500gf). If excessive force is applied,
the trimmer potentiometer may not function due to
damage.
please use adhesive resin without chlorine or
sulfur (Three-bond "1401 series") and evaluate
performance with your product. Lock paint may
cause corroison or electrical contact problems.
Temp. (T1)
Soldering Iron Power Output
150
C
Pre-heating
PV12/PV37/PV36 Series Notice
30 max.
W
60 to 120
Time (t1)
sec.
Limit Profile
Temp. (T3)
260
C
Heating
Cycle of Soldering Iron
Time (t2)
3 max.
sec.
Time
1
of Flow
Cycle
Time
1
R50E.pdf
47
08.8.26
8