BNX025H01B Murata, BNX025H01B Datasheet - Page 46

• Manufacturer Part Number: BNX025H01B
• Manufacturer: Murata

Specifications of BNX025H01B

• Lead Free Status / RoHS Status: Supplier Unconfirmed

2
!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
c
<Unless otherwise specified>
c
1. Electrical Performance
2. Mechanical Performance
44
No.
No.
Specifications and Test Methods
1
2
3
4
1
2
3
4
Temperature: Ordinary Temp. 15 to 35 C
Humidity: Ordinary Humidity 25 to 85% (RH)
Test and Measurement Conditions
Specifications
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Capacitance (Cap.)
Insulation Resistance
(I.R.)
Withstanding Voltage
DC Resistance (Rdc1, 2)
Appearance and
Dimensions
Solderability
Resistance to
Soldering Heat
Bonding Strength
Item
Item
Within the specified tolerance.
1000M min.
Products should not be damaged.
22 to 2200pF: 0.3 max.
22000 to 470000pF: 0.03 max.
Meet dimensions.
Electrodes should be at least 90% covered with new solder coating.
Meet Table 1.
Table 1
The electrodes should show no failure after testing.
Cap. Change
Appearance
Rdc 1, 2
(% C)
I.R.
22000 to 470000pF
22 to 2200pF
Specifications
Specifications
Within
1000M min.
No damage
7.5%
0.05 max.
0.5 max.
<In case of doubt>
Temperature: 20 2 C
Humidity: 60 to 70% (RH)
Atmospheric Pressure: 86 to 106kPa
Frequency
Voltage: 1 0.2Vrms
Voltage: Rated Voltage
Charging Time: 2 minutes max.
Test Voltage
Testing Time: 1 to 5s
Charge/Discharge Current: 50mA max.
Measured with 100mA max.
Rdc1: between signal terminals
Rdc2: between ground terminals
Visual Inspection and measured with micrometer.
Flux: Ethanol solution of rosin, 25wt%
Pre-heating: 150 10 C, 60 to 90s
Solder: qSn/Pb=60/40
Solder Temperature: q230 5 C
Immersion Time: q2 0.5s
Immersion and emersion rates: 25mm/s
Flux: Ethanol solution of rosin, 25wt%
Pre-heating: 150 10 C, 60 to 90s
Solder: Sn/Pb = 60/40 or Sn-30Ag-0.5Cu solder
Solder Temperature: 270
Immersion Time: 10 1s
Immersion and emersion rates: 25mm/s
Initial values: About 220 to 470000pF, measured after heat
treatment (150
condition for 48 4 hrs.
Then measured after exposure in room conditions for the
following hours.
It should be soldered on the glass-epoxy substrate.
Applying Force: 17.6N
Applying Time: 60s
22 to 100pF: 24 2 hrs.
220 to 470000pF: 48 4 hrs.
22 to 100pF
220 to 470000pF
wSn-3.0Ag-0.5Cu solder
Rdc1
0
10
22 to 22000pF
100000 to 470000pF
w3 1s
C, 1 hour) and exposure in the room
w240 3 C
Rdc2
Test Methods
Test Methods
5 C
Continued on the following page.
Rdc2
0.6
1.0 0.1MHz
1.0 0.1kHz
1.0
0.8
Rdc1
150Vdc
30Vdc
0.6
(in mm)
C50E.pdf
1
08.8.28