MKT1813415255 Vishay, MKT1813415255 Datasheet - Page 12

• Manufacturer Part Number: MKT1813415255
• Manufacturer: Vishay

Specifications of MKT1813415255

• Tolerance (+ Or -): 10%
• Voltage: 250VDC/160VAC
• Temp Coeff (dielectric): PLYE
• Mounting Style: Through Hole
• Construction: Axial
• Failure Rate: Not Required
• Seated Plane Height: Not Requiredmm
• Product Diameter (mm): 7mm
• Product Height (mm): Not Requiredmm
• Product Depth (mm): Not Requiredmm
• Product Length (mm): 14mm
• Lead Spacing (nom): Not Requiredmm
• Lead Diameter (nom): 0.7mm
• Operating Temp Range: -55C to 100C
• Capacitance: .15uF
• Package / Case: Not Required
• Lead Free Status / RoHS Status: Compliant

MKT 1813
Vishay Roederstein
www.vishay.com
28
SUB-CLAUSE NUMBER AND TEST
4.11.3
SUB-GROUP C3
4.12
4.12.1
4.12.5
SUB-GROUP C4
4.13
4.13.1
4.13.3
Final measurements
Endurance
Initial measurements
Final measurements
Charge and discharge
Initial measurements
Final measurements
For technical questions, contact: [e-mail]
CONDITIONS
Voltage proof = U
after removal from testchamber
Visual examination
Capacitance
Tangent of loss angle
Insulation resistance
Duration: 2000 h
1.25 x U
1.0 x U
Capacitance
Tangent of loss angle:
Visual examination
Capacitance
Tangent of loss angle
Insulation resistance
10 000 cycles
Charged to U
Discharge resistance:
Capacitance
Tangent of loss angle:
Capacitance
Tangent of loss angle
Insulation resistance
For C ≤ 470 nF at 100 kHz or
for C > 470 nF at 10 kHz
For C ≤ 470 nF at 100 kHz or
for C > 470 nF at 10 kHz
Rdc
R
DC Film Capacitor
Rdc
MKT Axial Type
=
at 100 °C
at 85 °C
------------------------------------------------- -
C
Rdc
×
2.5
Rdc
×
U
for 1 min within 15 min
(
R
dU dt
⁄
)
R
PERFORMANCE REQUIREMENTS
No breakdown of flash-over
No visible damage
Legible marking
|ΔC/C| ≤ 5 % of the value measured in
4.11.1.
Increase of tan δ ≤ 0.005
Compared to values measured in 4.11.1
≥ 50 % of values specified in section
“Insulation resistance” of this specification
No visible damage
Legible marking
|ΔC/C| ≤ 5 % compared to values measured
in 4.12.1
Increase of tan δ
Compared to values measured in 4.12.1
≥ 50 % of values specified in section
“Insulation resistance” of this specification
|ΔC/C| ≤ 3 % compared to values measured
in 4.13.1
Increase of tan δ
Compared to values measured in 4.13.1
≥ 50 % of values specified in section
“Insulation resistance” of this specification
≤ 0.005 for:
C ≤ 100 nF or
≤ 0.010 for:
100 nF < C ≤ 220 nF or
≤ 0.015 for:
220 nF < C ≤ 470 nF and
≤ 0.003 for:
C > 470 nF
≤ 0.005 for:
C ≤ 100 nF or
≤ 0.010 for:
100 nF < C ≤ 220 nF or
≤ 0.015 for:
220 nF < C ≤ 470 nF and
≤ 0.003 for:
C > 470 nF
Document Number: 26013
Revision: 08-Dec-08