D-436-86 Tyco Electronics, D-436-86 Datasheet - Page 2

• Manufacturer Part Number: D-436-86
• Description: CONN SPLICE BUTT 16AWG BLU/BLU
• Manufacturer: Tyco Electronics

Specifications of D-436-86

• Terminal Type: Butt Splice, Inline, Individual Openings
• Number Of Wire Entries: 2
• Termination: Crimp
• Wire Gauge: 16 AWG
• Insulation: Fully Insulated
• Features: Heat Shrink
• Color: Blue, Blue Stripe
• Connector Type: Butt Splice
• Insulator Color: Blue
• Termination Method: Crimp
• Wire Size (awg): 20-16
• Contact Material: Copper
• Contact Plating: Nickel
• Insulator Material: PVDF
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 1-1195133-8; 650130-000

APPLICATION
1. These parts are designed to provide an immersion resistant in-line splices of 2 or 3 to 1 wires falling within
2. Parts are available only as an assembly of one of each Item #1 and Item #2.
3. Parts are to be installed per Thermofit Assembly Procedure, see below.
4. Inside diameter and outside diameter of splice are to be measured in crimp areas, 2.54 to 5.08 (0.100 to 0.200)
5. Acceptance sampling shall be in accordance with Paragraph 4.6.1 of MIL-T-7928.
6. Packing and packaging shall be in accordance with Section 5, Level C, of MIL-T-7928.
7. This document takes precedence over documents referenced herein.
1.0
2.0
3.0
UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS.
INCHES DIMENSIONS ARE BETWEEN BRACKETS.
TOLERANCES:
0.00 N/A
0.0 N/A
0 N/A
DRAWN BY:
If this document is printed it becomes uncontrolled. Check for the latest revision.
from ends of part. Slight burr permitted on parted surfaces.
the size range listed on sheet 1, having insulations rated for at least 135 C.
M. FORONDA
SCOPE
This document outlines the procedure to be followed to obtain immersion resistant 3 or 2 to 1 in-line
splices using Thermofit In-Line Splice Sealing System D-436-85/-87.
PROCEDURE:
a) Strip all wires 7.92 (0.312) to 8.74 (0.344).
b) Attach the single lead to the appropriate size crimp splice using a Raychem AD-1377 Crimp Tool.
c) Pass the wires to be attached to other barrel through the sealing sleeve from the three hole insert end.
d) Insert wires into barrel and crimp. Care must be taken so that the wires remain untwisted between the
e) Apply heat, using a recommended heat source, first to the three-hole insert and then to the other.
RECOMMENDED RAYCHEM HEATING TOOLS
Thermogun #500A
Shop Air Heater #CV-4504
Mini-Gun #CV-5300
Heater
Heat should be applied until insert melts and flows axially along the wire.
crimp splice and the three wire seal or the sealing sleeve cannot be positioned properly.
ANGLES: N/A
ROUGHNESS IN
MICRON
Menlo Park, CA 94025, USA
Tyco Electronics Corporation
305 Constitution Drive
REPLACES:
SPECIFICATION CONTROL DRAWING
Tyco Electronics reserves the right to amend this
drawing at any time. Users should evaluate the
suitability of the product for their application.
N/A
THERMOFIT ASSEMBLY PROCEDURE
DCR NUMBER:
D001297
Raychem
Reflector
TG-14
991180
991319
Products
TITLE :
DOCUMENT NO.:
DATE:
PROD. REV.
SEE TABLE
IN-LINE SPLICE SEALING SYSTEM,
2 OR 3 TO 1 SPLICER: Nickel Plated,
Color Coded, with Inspection Slots
05-Dec.-00
D-436-85/-87
(Low Outgassing)
SCALE:
None
SIZE:
A
DOC ISSUE:
1
SHEET:
2 of 2