TFBS4710-TT3 Vishay, TFBS4710-TT3 Datasheet - Page 2
![no-image](/images/manufacturer_photos/0/6/697/vishay_sml.jpg)
TFBS4710-TT3
Manufacturer Part Number
TFBS4710-TT3
Description
Infrared Transceivers SIR 115.2 kbits/s 2.7-5.5V Op Voltage
Manufacturer
Vishay
Type
TX/RXr
Datasheet
1.TFBS4710-TT3.pdf
(11 pages)
Specifications of TFBS4710-TT3
Data Rate
115.2Kbps
Peak Wavelength
900nm
Angle Of Half Sensitivity
48°
Pulse Width
2us
Radiant Intensity
0.07W/sr
Communication Distance
100
Led Supply Voltage
-0.5 to 6V
Package Type
Ultra Small Profile
Fall Time
100ns
Rise Time
100ns
Dimensions
8.96x3.33x2.74
Operating Supply Voltage (typ)
2.5/3.3/5V
Operating Supply Voltage (min)
2.4V
Operating Supply Voltage (max)
5.5V
Mounting
Surface Mount
Pin Count
6
Operating Temp Range
-25C to 85C
Operating Temperature Classification
Commercial
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Functional Block Diagram
Pinout
TFBS4710
weight 100 mg
Pin Description
Document Number 82612
Rev. 1.5, 03-Jul-06
Pin Number
1
2
3
4
5
6
18511
Function
Anode
IRED
1
RXD
GND
TXD
V
SD
CC
18282
2
IRED Anode is connected to a power supply. The LED current can be decreased
protection circuit disables the LED driver if the TXD pin is asserted for longer than
Shutdown. Setting this pin active for more than 1.5 ms switches the device into
TXD
SD
during received pulses. It is capable of driving a standard CMOS or TTL load.
by adding a resistor in series between the power supply and IRED Anode. A
Received Data Output, normally stays high but goes low for a fixed duration
3
This Input is used to turn on IRED transmitter when SD is low. An on-chip
4
separate unregulated power supply can be used at this pin.
5
6
Amplifier
Regulated Supply Voltage
shutdown mode
Description
Comparator
Ground
Logic
&
Control
80 µs
Definitions:
In the Vishay transceiver data sheets the following nomenclature is
used for defining the IrDA operating modes:
SIR: 2.4 kbit/s to 115.2 kbit/s, equivalent to the basic serial infrared
standard with the physical layer version IrPhy 1.0
MIR: 576 kbit/s to 1152 kbit/s
FIR: 4 Mbit/s
VFIR: 16 Mbit/s
MIR and FIR were implemented with IrPhy 1.1, followed by IrPhy 1.2,
adding the SIR Low Power Standard. IrPhy 1.3 extended the Low
Power Option to MIR and FIR and VFIR was added with IrPhy 1.4.
A new version of the standard in any case obsoletes the former ver-
sion.
With introducing the updated versions the old versions are obso-
lete. Therefore the only valid IrDA standard is the actual version
IrPhy 1.4 (in Oct. 2002).
GND
V CC1
Controlled Driver
Push-Pull
Driver
Vishay Semiconductors
RED C
V CC2
RXD
I/O
TFBS4710
O
I
I
www.vishay.com
Active
HIGH
HIGH
LOW
143