FN3026HL-50-72 Schaffner EMC Inc, FN3026HL-50-72 Datasheet - Page 2

• Manufacturer Part Number: FN3026HL-50-72
• Description: Compact 3-phase Low-leakage Plastic Filters
• Manufacturer: Schaffner EMC Inc
• Series: FN 3026r

Specifications of FN3026HL-50-72

• Filter Type: Power Line
• Voltage - Rated: 300V, 520V
• Current: 50A
• Mounting Type: DIN Rail
• Termination Style: Terminal Block
• Voltage Rating: 300 VAC
• Current Rating: 50 A
• Mounting Style: DIN Rail
• Filtered: Yes
• Frequency: 60 Hz
• Leakage Current: 2.5 mA
• Product: Power Line Filters
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Inductance: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 802-141; 817-1124

Filter selection table
Filter
FN 3025HL-10-71
FN 3025HL-20-71
FN 3025HL-30-71
FN 3025HL-50-72
FN 3025HP-10-71
FN 3025HP-20-71
FN 3025HP-30-71
FN 3025HP-50-72
FN 3026HL-10-71
FN 3026HL-20-71
FN 3026HL-30-71
FN 3026HL-50-72
FN 3026HP-10-71
*
**
Typical filter attenuation
Per CISPR 17; A = 50Ω/50Ω sym; B = 50Ω/50Ω asym; C = 0.1Ω/100Ω sym; D = 100Ω/0.1Ω sym
10 and 20A HL types
Installation
FN 3026HP-20-71
FN 3026HP-30-71
FN 3026HP-50-72
> Components
Calculated at rated current, 480VAC and cos phi = 0.8. The exact value depends upon the efficiency of the drive, the motor and the entire application.
Maximum leakage under normal operating conditions. Note: if two phases are interrupted, worst case leakage could reach up to 10 times higher levels (at 520VAC/60Hz).
> FN 3025 / FN 3026
Rated current
@ 50°C (40°C)
10 (10.7)
20 (21.4)
30 (32.1)
50 (53.5)
10 (10.7)
20 (21.4)
30 (32.1)
50 (53.5)
10 (10.7)
20 (21.4)
30 (32.1)
50 (53.5)
10 (10.7)
20 (21.4)
30 (32.1)
50 (53.5)
10 and 20A HP types
[A]
power rating*
Typical drive
[kW]
18.5
18.5
18.5
18.5
5.5
5.5
5.5
5.5
11
30
11
30
11
30
11
30
Leakage current**
@ 480VAC/50Hz
30 and 50A HL types
[mA]
0.4
0.4
0.4
0.4
2.5
2.5
2.5
2.5
0.4
0.4
0.4
0.4
2.5
2.5
2.5
2.5
@ 25°C/50Hz
Power loss
FN 3025/FN 3026 are delivered with closed
plastic covers and unfastened terminals. To
install the filter please proceed as follows:
n
n
n
n
n
n
10.5
10.5
10.5
10.5
[W]
4.8
6.2
7.0
4.8
6.2
7.0
4.8
6.2
7.0
4.8
6.2
7.0
Mount the filter on a metal surface with
four screws or snap it onto a TS 35 DIN-
rail.
First connect the green/yellow wire to the
earth stud of the filter.
Gently lift the two hinged plastic covers.
Connect phase wires with cable lugs by
pushing down and tightening the screws.
Please note the torque recommendation on
top of the filter.
Push the covers back into their locked
position to finish the filter installation.
30 and 50A HP types
Input/Output
connections
496-405F August 2009
-71
-71
-71
-72
-71
-71
-71
-72
-71
-71
-71
-72
-71
-71
-71
-72
Page 2/3
Weight
0.52
0.52
0.54
0.93
0.52
0.52
0.54
0.93
0.56
0.56
0.58
0.98
0.56
0.56
0.58
0.98
[kg]