MF0W2FFE006KIL MULTICOMP, MF0W2FFE006KIL Datasheet - Page 3

• Manufacturer Part Number: MF0W2FFE006KIL
• Description: RESISTORS KIT, 0.5W 1% E6RESISTOR KIT, 0.5W 1% E6
• Manufacturer: MULTICOMP
• Series: MF50r

Specifications of MF0W2FFE006KIL

• Power Rating: 0.5W
• Tolerance, +: 1%
• Tolerance, -: 1%
• Temp, Op. Max: 155(DEGREE C)
• Temp, Op. Min: -55(DEGREE C)
• Voltage Rating, Dc: 350V
• Temp. Coeff, +: 50PPM/(DEGREE C)
• Rohs Compliant: YES

*RCWV= Rat ed Cont inuous Working Volt age =
Temperature coefficient
Dielectric withstanding
R esistance to soldering
S hort - time overload
R esistance to solvent
Temperature cycling
Load life in humidity
JIS - C - 5202 7.10
JIS - C - 5202 5.2
JIS - C - 5202 5.7
JIS - C - 5202 7.4
JIS - C - 5202 5.5
JIS - C - 5202 5.8
JIS - C - 5202 7.9
JIS - C - 5202 6.1
JIS - C - 5202 6.4
JIS - C - 5202 6.5
JIS - C - 5202 6.9
Characteristics
Terminal strength
Pulse overload
Performance Specificat ions
S olderability
Load life
voltage
heat
Natural resistance change per temp. degree centigrade.
R
R
R esistors shall be clamped in the trough of a 90 °metallic V-
block and shall be tested at AC potential respectively
specified in the above list for 60 + 10 / -0 seconds.
R esistance change after continuous five cycles for duty cycle
specified
Permanent resistance change after the application of a
potential of 2.5 times RCWV for 5 seconds
R esistance change after 10,000cycles (1 second “ on” , 25
seconds “ off” ) at 4 times RCWV .
R esistance change after 1,000 hours (1.5 hours “ on” , 0.5 hour
“ off” ) at RCWV in a humidity test chamber controlled at 40
± 2
Permanent resistance change after 1,000 hours operating at
RCWV with duty cycle of 1.5 hours “ on” , 0.5 hour “ off” at 70
Direct load: R esistance to a 2.5 kgs direct load for 10 seconds
in the direction of the longitudinal axis of the terminal leads.
Twist test: Terminal leads shall be bent through 90 ° at a
point of about 6mm from the body of the resistor and shall be
rotated through 360 ° about the original axis of the bent
terminal in alternating direction for a total of 3 rotations.
Permanent resistance change when leads immersed to 3.2 -
4.8mm from the body in 350
seconds
The area covered with a new, smooth, clean, shiny and
continuous surface free from concentrated pinholes.
Test temp. of solder: 235
Dwell time in solder: 3 +0.5/ -0 seconds
S pecimens shall be immersed in a bath of trichroethane
completely for 3 mins with ultrasonic.
1
2
: R esistance value at room temperature (t
: R esistance value at room temp. plus 100
R
Step
R
± 2
1
(t
2
1
2
3
4
-R
2
and 90 to 95% relative humidity.
P
P
-t
1
1
r
r
)
ambient
e
e
x 10
c
c
Temperature
+155
i
i
−55
R oom temp.
R oom temp.
6
s
s
i
i
(PPM /
o
o
n
n
± 3
± 3
Test Methods
Rat ed Power × Resist ance Value
M
M
)
± 5
e
e
t
t
± 10
a
a
l
l
F
F
solder for 3 ± 0.5
16
i
i
30 mins
10 - 15 mins
30 mins
10 - 15 mins
l
l
m
m
1
)
Time
F
(t
F
2
i
i
)
x
x
e
e
d
d
R
R
e
e
Within the temperature coefficient
specified below
No evidence of flashover mechanical
damage, arcing or insulation breaks down.
R esistance change rate is ± (1% + 0.05Ω).
No evidence of mechanical damage.
R esistance change rate is ± (0.5% + 0.05Ω).
No evidence of mechanical damage.
R esistance change rate is ± (1% + 0.05Ω).
No evidence of mechanical damage.
No evidence of mechanical damage.
R esistance change rate is ± (1% + 0.05Ω ).
No evidence of mechanical damage.
95% coverage Min.
No deterioration of protective coating and
markings.
s
s
i
i
s
s
Resistance value
Normal type
Non-Flame type
Resistance value
Normal type
Non-Flame type
t
t
± 15 PPM /
± 25 PPM /
± 50 PPM /
o
o
r
r
s
s
Max. T.C.R.
Limits
± 100 PPM /
± 200 PPM /
± 1.5%
± 5%
± 1.5%
± 5%
R/R
R/R