MC0805WAF1201T5E-TC MULTICOMP, MC0805WAF1201T5E-TC Datasheet - Page 2
![RESISTOR, THICK FILM, 1.2KOHM, 100mW, 1%](/photos/26/6/260651/3761524_sml.jpg)
MC0805WAF1201T5E-TC
Manufacturer Part Number
MC0805WAF1201T5E-TC
Description
RESISTOR, THICK FILM, 1.2KOHM, 100mW, 1%
Manufacturer
MULTICOMP
Series
MCRMCr
Datasheet
1.MC0805WA00000T5E-TC.pdf
(5 pages)
Specifications of MC0805WAF1201T5E-TC
Resistance
1.2kohm
Resistance Tolerance
± 1%
Power Rating
100mW
Voltage Rating
150V
Resistor Element Material
Thick Film
Temperature Coefficient
± 100ppm/°C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Short time overload
Insulation resistance
Dielectric withstanding
Load life in humidity
Load Life
Temperature coefficient
voltage
Terminal bending
Temperature cycling
Soldering Heat
Solderability
Characteristics
10O-100 O
101 O-1MO
Resistance change rate is:
1,000 MO or more
No evidence of flashover
mechanical damage, arcing or
insulation break down
± (1.0 % + 0.1
± (1.0 % + 0.05O) Max.
± (0.5 % + 0.05O) Max.
Resistance change rate is
± (1.0 % + 0.1
Resistance change rate is
± (1.0 % + 0.1
Electrical characterisstics shall be
satisfied. Wthout distinct
deformation in appearance.
95 % coverage Min.
Performance specification
Limits
± 200 PPM/°C
± 100 PPM/°C
) Max.
) Max.
) Max.
R1: Resistance value at room temperature (t1)
R2: Resistance value at room temp. plus 100°C (t2)
7.9 Resistance change after 1,000 hours (1.5 hours
hour "off" ) at RCWV in a humidity chamber controlled at
7.10 Permanent resistance change after 1,000 hours
hour "off") at 70°C ±2°C ambient
6.5 Test temperature of solder : 245 °C ± 3°C
Dipping them solder : 2 - 3 seconds
5.2 Natural resistance change per temp. degree centigrade
5.5 Permanent resistance change after the application
of a potential of 2.5 times RCWV for 5 seconds
5.6 Apply 500V DC between protective coating and
termination for 1 min, then measure
5.7 Apply 500V AC between protective coating and
termination for 1 minute
6.1.4 Twist of Test Board:
Y/X = 5/90 mm for 10 seconds
7.4 Resistance change after continuous 5 cycles for
duty cycle specified below:
40°C ±2°C and 90 to 95
operating at RCWV, with duty cycle of (1.5 hours"on", 0.5
soldering iron method
Solder bath method
Reflow soldering method
Peak:
R1(t2-t1)
R2-R1
Test Methods (JIS - C - 5201-1)
Bit temperature: 350 ± 10°C
Application time of soldering iron : 3+ 1/-0 sec.
Step
X 10
1
2
3
4
6
Temperature
-55°C ±3°C
Room temp.
-125°C ±2°C
Room temp.
(PPM/°C)
Pre-heat: 100 to 105°C, 30 ± 5 sec
Temperature: 265 ± 3°C, 5 + 1/-0 sec.
250 + 5/-0°C
230 °C or higher
% relative humidiity
30 mins
10 ~ 15 mins
30 mins
10 ~ 15 mins
Time
30 ± 10 sec.
"on", 0.5