29 0016 ALPS, 29 0016 Datasheet - Page 3

• Manufacturer Part Number: 29 0016
• Description: POTENTIOMETER, 10KB
• Manufacturer: ALPS
• Series: RK09r

Specifications of 29 0016

• Track Resistance: 10kohm
• Track Taper: Linear
• No. Of Turns: 1
• Resistance Tolerance: ± 20%
• Voltage Rating: 20V
• Power Rating: 50mW
• No. Of Gangs: 1
• Resistor Element: RoHS Compliant
• Adjustment Type: Vertical
• Potentiometer Mounting: PCB
• Rohs Compliant: Yes

SYHB
NOTE
ENDURANCE
MECHANICAL
ELECTRICAL
2. Operating temperature :-IO C-+60 C. 3. Storage temperature :-30 C-*+70°C.
DATE
8. Robustness of shaft against end thrust • -
9. Robustness of shaft against side thrust =
1. The items except above menjionedeitems shall meet or exceed JIS C 6443.
7. Eccentricity of shaft •'
4. Start ing toruoue
6. Play of shaft
4. Residual
8. Taoer
2. Operation torque
3. Shaft end stoo strength
5. Resistance to soldering heat :
7. Withstand voltage* More than 1 minute with an application of A. C. 250 V.
5. Sliding noise
6. Insulation resistance : Greater than 100 Ha measured by D. C. 250V.
1. Overall rotational angle = 280°±5°
2. Rated power
3. Rated vol tase
1. Total resistance : 10k n ±20*
1. -Rt) I a t i on a I
3 seconds.
The shaft shall withstand aeainst side thrust of not less than 4 Kgf-cra for
3 seconds on the end of the shaft at right angles to the axis of the shaft
after mounting the resistor by soldering.
center of the mounting Position.
The shaft shall withstand asainst end thrust of not less than 5 K«f for
After solderine (Less than 300*C and Quicker than 3 seconds) there shall be no
The resistor shall be mounted by soldering the mounting leas on the oanel.
and a side thrust of 250 •f-cm at the end of the shaft shall be applied,
The eccentricity of the root of shaft shall not exceed 0. 35nm against the
evidence of ooor contact between resistance element and terminals, or any
Physical daraaees as a result of the test.
then the total slay of the shaft shall not exceed 0.5x l / 20 ran p-p.
The rated voltage shall be the voltage of D.C. or A. C.
however,
rated voltage exceeds the maximum work)no voltaae given in the following,
APPO
(conmercial frequency .effective value ) correspond ins to the rated oower
(dissipation), and be obtained from the folfowino formula. When the obtained
Maximum working voltaoe : 50 V A. C. . 20 V D. C.
Where
CHKD
the max inum_i»or kino voltage of the following shall be the rated voltage.
resistance between terminals
life
osoo
P = Rated oower (dissipation)
R : Nominal total resistance to)
E = /p^R (V)
E : Rated voltase (V)
between
=
II
: B
=
: 0. 05 W
:
Sep. 13. 'SS
APPO.
S. Aiiana
Less than 100 mV measured by method of J IS C 6443.
*m ALPS ELECTRIC CO., LTD.
5. 000 cycles min.
SPECIFICATIONS
term. I&2.
: 10-80 sf-cm
'• 3 Kflf-cm MIN.
: 100 gf-cm MAX.
I
Set. 13. 'SB
CHKO.
M, Sal oh
1 ' I
I
I Saitoh
See. 13. 'SS
OSCD.
term. 243
I' »
(W)
DOCUMENT NO.
TITLE
W1 0 1 1 762M
: 300Q max.
I
U V