CWR11MH475KC Kemet, CWR11MH475KC Datasheet
CWR11MH475KC
Specifications of CWR11MH475KC
Related parts for CWR11MH475KC
CWR11MH475KC Summary of contents
Page 1
... Sn Solder SPICE For a detailed analysis of specific part numbers, please visit kemet.com for a free download of KEMET's SPICE software. The KEMET SPICE program is freeware intended to aid design engineers in analyzing the performance of these capacitors over frequency, temperature, ripple, and DC bias conditions. ...
Page 2
... Refer to Part Number Electrical Specification Table ESR (100kHz) Refer to Part Number Electrical Specification Table Leakage Current ≤ 0.01CV (µA) at Rated Voltage after 5 minutes © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com 156 K 020 Capacitance ...
Page 3
... Mil-Std-202, Meth. 204, Cond. D, 10Hz to 2000Hz, 20G Peak Additional qualification tests per MIL-PRF-55365/8 *IL = Initial Limit Certification Mil-PRF-55365/8 © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com Condition ΔC/C DF DCL Characteristics ΔC/C Within ± 10% of initial value ...
Page 4
... Notes: (Ref) – Dimensions provided for reference only. No dimensions provided for because low profile cases do not have a bevel or a notch. * MIL-C-55365/8 specified dimensions © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com 1,000,000 10,000,000 Component F* ± ...
Page 5
... Also available on large (13 inch) reels. Add 7280 to the end of the part number. Higher voltage ratings and tighter tolerance product including ESR may be substituted within the same size at KEMET's option. Voltage substitutions will be marked with the higher voltage rating. Substitutions can include better than series. ...
Page 6
... Also available on large (13 inch) reels. Add 7280 to the end of the part number. Higher voltage ratings and tighter tolerance product including ESR may be substituted within the same size at KEMET's option. Voltage substitutions will be marked with the higher voltage rating. Substitutions can include better than series. ...
Page 7
... E 7260-38 R 2012-12 S 3216-12 T 3528-12 U 6032-15 V 7343-20 T510X 7343-43 T510E 7260-38 © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com 67% 33% 125 mWatts @ 25°C w/+20°C Rise 75 85 110 150 165 200 125 270 285 ...
Page 8
... IPC standard 7351 (IPC-7351). ¹ Height of these chips may create problems in wave soldering. ² Land pattern geometry is too small for silkscreen outline. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com 5% of Rated Voltage 1% of Rated Voltage ...
Page 9
... Case Size and X **Case Size and Z Construction MNO / Silver Paint Leadframe (-Cathode) Carbon Tantalum Wire © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com smax T smin 25 Pb-Free Assembly 150°C 200°C 60-120 sec 3°C/sec max 217° ...
Page 10
... In addition, packaging materials will be degraded by high temperature - reels may soften or warp, and tape peel force may increase. KEMET recommends that maximum storage temperature not exceed 40 degrees C, and maximum storage humidity not exceed 60% relative humidity. In addition, temperature fluctuations should be minimized to avoid condensation on the parts, and atmospheres should be free of chlorine and sulphur bearing compounds ...
Page 11
... X 7343- 7260- c-spec required for 7" reel packaging. C-7280 required for 13" reel packaging. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com 7" Reel* 13" Reel* 2,500 10,000 3,000 12,000 2,500 10,000 2,500 ...
Page 12
... B are measured on a plane 0.3mm above the bottom of the pocket (f) see Addendum in EIA Document 481 for standards relating to more precise taping requirements. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com P 2 [10 pitches cumulative Po tolerance on tape ± ...
Page 13
... Tape 0.5 mm maximum 0.5 mm maximum Figure 5 – Bending Radius Embossed Punched Carrier Carrier Bending R R Radius © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com Peel Strength Maximum Component Rotation Maximum ° ° s Rotation ( ) ...
Page 14
... Tape Size N Min 8mm 12mm (1.969) 16mm © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com Access Hole at Slot Location (Ø min.) C (Arbor hole diameter) If present, tape slot in core for tape start: 2 ...
Page 15
... Figure 8 – Maximum Camber Elongated sprocket holes (32 mm & wider tapes maximum, either direction Straight Edge 250 mm © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com Carrier Tape Round Sprocket Holes START 100 mm Min. Leader ...
Page 16
... Although all product-related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicated or that other measures may not be required. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com Tools http://capacitoredge ...
Page 17
... Tel: 52-33-3123-2141 Note: KEMET reserves the right to modify minor details of internal and external construction at any time in the interest of product improvement. KEMET does not assume any responsibility for infringement that might result from the use of KEMET Capacitors in potential circuit designs. KEMET is a registered trademark of KEMET Electronics Corporation. © ...