23698 Loctite, 23698 Datasheet - Page 2

• Manufacturer Part Number: 23698
• Description: LIGHT CURE LIQUID ADH, BOTTLE, 1L
• Manufacturer: Loctite
• Series: 3106r

Specifications of 23698

• Color: Clear
• Dispensing Method: Bottle
• Volume: 1l
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Curing System: Electrodeless, D bulb
Curing System: Electrodeless, H bulb
TYPICAL PROPERTIES OF CURED MATERIAL
TYPICAL PERFORMANCE OF CURED MATERIAL
Henkel Loctite Americas
+860.571.5100
Cured @ 30 mW/cm², measured @ 365 nm, for 80 seconds using
a glass filtered metal halide light source
Adhesive Properties
Cured @ 30 mW/cm², measured @ 365 nm, for 80 seconds using
a metal halide light source, (samples with 0.5 mm gap).
Physical Properties:
Electrical Properties:
Lap Shear Strength, ISO 4587:
Shore Hardness, ISO 868, Durometer D
Refractive Index
Water Absorption, ISO 62, %:
Elongation, at break, ISO 527-3, %
Tensile Modulus, ISO 527-3
Tensile Strength, at break, ISO 527-3
Surface Resistivity, IEC 60093, Ω∙cm
Volume Resistivity, IEC 60093, Ω·cm
Dielectric Breakdown Strength, , kV/mm
Dielectric Constant / Dissipation Factor, IEC 60250:
Polycarbonate
2 hours in boiling water
100-Hz
1-kHz
1-MHz
* substrate failure
14
12
10
14
12
10
8
6
4
2
0
8
6
4
2
0
0
0
For the most direct access to local sales and technical support visit: www.loctite.com
10
10
20
20
30
30
40
40
N/mm² 255
(psi)
N/mm² 18.6
(psi)
N/mm² *5.2
(psi)
50
50
(37,000)
(2,700)
(750)
53
1.5
250
9.2×10
7.7×10
26
3.18
5.17 / 0.04
5.01 / 0.02
4.61 / 0.04
Henkel Loctite Europe
14
14
+49.89.9268.0
60
60
TYPICAL ENVIRONMENTAL RESISTANCE
Chemical/Solvent Resistance
Aged under conditions indicated and tested @ 22 °C.
Heat Aging
GENERAL INFORMATION
This product is not recommended for use in pure oxygen
and/or oxygen rich systems and should not be selected as
a sealant for chlorine or other strong oxidizing materials.
For safe handling information on this product, consult the
Material Safety Data Sheet (MSDS).
Where aqueous washing systems are used to clean the
surfaces before bonding, it is important to check for
compatibility of the washing solution with the adhesive. In
some cases these aqueous washes can affect the cure and
performance of the adhesive.
This product is not normally recommended for use on plastics
(particularly thermoplastic materials where stress cracking of
the plastic could result). Users are recommended to confirm
compatibility of the product with such substrates.
Directions for use
Environment
Boiling water
Water immersion
Water immersion
Isopropanol immersion
Heat/humidity
Cured @ 30 mW/cm², measured @ 365 nm, for 80 seconds using
a metal halide light source, (samples with 0.5 mm gap).
1. This product is light sensitive; exposure to daylight, UV
2. The product should be dispensed from applicators with
3. For best performance bond surfaces should be clean and
4. Cure rate is dependent on lamp intensity, distance from
5. Recommended intensity for cure in bondline situation is 5
Lap Shear Strength, ISO 4587:
Lap Shear Strength, ISO 4587, % of initial strength:
Polycarbonate:
Polycarbonate:
light and artificial lighting should be kept to a minimum
during storage and handling.
black feedlines.
free from grease.
light source, depth of cure needed or bondline gap and
light transmittance of the substrate through which the
radiation must pass.
mW/cm² minimum (measured at the bondline) with an
exposure time of 4-5 times the fixture time at the same
intensity.
0.5 mm gap
Aged @ 71 °C for 170 hours
Aged @ 71 °C for 340 hours
Aged @ 93 °C for 170 hours
Aged @ 93 °C for 340 hours
* substrate failure
100
°C
49
87
22
38
TDS LOCTITE
--------
--------
* 100
* 100
* 100
2 h
% of initial strength
Henkel Loctite Asia Pacific
®
--------
--------
--------
--------
3106™, April-2007
24 h
95
+81.45.758.1810
*100
*100
*100
*100
--------
--------
--------
--------
170 h
* 100