18636 Loctite, 18636 Datasheet

18636

Manufacturer Part Number

18636

Description

Adhesive Compound Accelerator

Manufacturer

Loctite

Datasheet

1.20352.pdf (2 pages)

Specifications of 18636

Color

Clear/Amber

Dispensing Method

Aerosol

Volume

0.7fl.oz. (US)

Drop Ship

Yes

Pack Quantity

Current page: 1 of 2
Download datasheet (59Kb)

PRODUCT DESCRIPTION

LOCTITE

characteristics:

LOCTITE

either pre- or post-applied to the bond. The product is

especially

adhesive to ensure rapid fixturing. Typical applications include

securing wires or coils to PCBs, tamper-proofing adjustable

components, mounting stand-offs, edge guides and board

stiffeners.

TYPICAL PROPERTIES

TYPICAL PERFORMANCE

Fixture time and cure speed achieved as a result of using

LOCTITE

substrate bonded.

Handling precautions

Activator must be handled in a manner applicable to highly

flammable materials and in compliance with relevant local

regulations.

The solvent can affect certain plastics or coatings. It is

recommended to check all surfaces for compatibility before

use.

GENERAL INFORMATION

This product is not recommended for use in pure oxygen

and/or oxygen rich systems and should not be selected

with a sealant for chlorine or other strong oxidizing

materials.

For safe handling information on this product, consult the

Material Safety Data Sheet (MSDS).

Technology

Chemical Type

Solvent

Active Ingredient

Concentration, %

Appearance

Viscosity

Cure

Application

Solidification Time, seconds:

Specific Gravity @ 25 °C

Viscosity @ 20 °C, mPa·s (cP)

Drying Time @ 20 °C, seconds

On Part Life, minutes

Infrared Spectroscopy

Flash Point - See MSDS

Steel with Loctite

cyanoacrylate adhesives is required. It can be

712™ is used where increased cure speed of

suited

712™ depend on the adhesive used and the

712™

495

for

provides

Cyanoacrylate Activator

Amine (active ingredient)

Isopropanol

1.7 to 2.3

Transparent liquid

Very low

Not applicable

CA adhesive cure accelerator

post-application

the

To match standard

following

LMS

cyanoacrylate

0.8

≤30

≤1

≤30

LMS

product

LMS

Under no circumstances should activator and adhesive be

mixed directly as liquids. Use only in a well ventilated area.

Directions for use

Post Activation

Surface Activation

Loctite Material Specification

LMS dated August-13, 1998. Test reports for each batch are

available for the indicated properties. LMS test reports include

selected QC test parameters considered appropriate to

specifications for customer use. Additionally, comprehensive

controls are in place to assure product quality and

consistency. Special customer specification requirements may

be coordinated through Henkel Quality.

Storage

This activator is classified as HIGHLY FLAMMABLE and

must be stored in an appropriate manner in compliance with

relevant regulations. Do not store near oxidising agents or

combustible materials. The product is light sensitve and

accordingly, translucent containers should be kept in a dark

place when not in use. Store product in the unopened

container in a dry location. Storage information may also be

indicated on the product container labelling.

Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or

greater than 28 °C can adversely affect product properties.

Material removed from containers may be contaminated during

use. Do not return product to the original container. Henkel

cannot assume responsibility for product which has been

contaminated or stored under conditions other than those

previously indicated. If additional information is required,

please contact your local Technical Service Center or

Customer Service Representative.

1. Apply Loctite cyanoacrylate to the parts to be bonded or

2. Apply Activator over all exposed cyanoacrylate adhesive

1. Apply one coating of Activator to the area to be bonded by

2. Allow LOCTITE

3. Apply the Loctite cyanoacrylate product immediately after

4. Activator can be re-applied if necessary if there is a delay

fixed.

by spray or drop. (Typically use one drop of activator per

drop of exposed adhesive).

spray, brush or dipping. Contaminated surfaces may need

special cleaning or degreasing prior to activation to

remove any soluble contamination.

to bonding to avoid solvent entrapment within the bond

joint.

drying or not more than

of more than

adhesive application.

LOCTITE

45-

712™ to fully evaporate from parts prior

seconds between original activator and

45-

LMS

seconds thereafter.

Technical Data Sheet

December-2008

712™

18636 Summary of contents

Page 1

... Use only in a well ventilated area. following product Directions for use Post Activation 1. Apply Loctite cyanoacrylate to the parts to be bonded or fixed. 2. Apply Activator over all exposed cyanoacrylate adhesive LMS by spray or drop. (Typically use one drop of activator per drop of exposed adhesive). ...

Page 2

... U.S. Patent and Trademark Office. Reference 1.1 Henkel Americas +860.571.5100 For the most direct access to local sales and technical support visit: www.henkel.com/industrial We cannot assume Henkel Europe +49.89.320800.1800 ® TDS LOCTITE 712™, December-2008 Henkel Asia Pacific +86.21.2891.8863 ...