60921 Loctite, 60921 Datasheet - Page 2

• Manufacturer Part Number: 60921
• Description: ACRYLIC ADHESIVE, BOTTLE, 10ML
• Manufacturer: Loctite
• Series: 609r

Specifications of 60921

• Adhesive Type: Acrylic
• Color: Green
• Dispensing Method: Bottle
• Volume: 10ml
• Mil Spec: Mil-R-46082B
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

TYPICAL PROPERTIES OF CURED MATERIAL
TYPICAL PERFORMANCE OF CURED MATERIAL
TYPICAL ENVIRONMENTAL RESISTANCE
Hot Strength
Tested at temperature
Henkel Loctite Americas
+860.571.5100
Adhesive Properties
After 24 hours @ 22 °C
After 1 hour @ 22 °C
Cured for 1 week @ 22 °C
Physical Properties:
Compressive Shear Strength, ISO 10123:
Compressive Shear Strength, ISO 10123:
Compressive Shear Strength, ISO 10123:
Coefficient of Thermal Expansion, ASTM D 696, K
Coefficient of Thermal Conductivity, ASTM C 177,
W/(m·K)
Specific Heat, kJ/(kg·K)
Elongation, at break, ASTM D 412, %
Steel pins and collars
Steel pins and collars
Steel pins and collars
100
125
100
75
50
25
75
50
25
1min
0
0
0
For the most direct access to local sales and technical support visit: www.loctite.com
5min 10min 30min 1h
50
100
N/mm²
(psi)
N/mm²
(psi)
3h 6h
150
-1
24h
(≥2,290)
(≥1,490)
≥15.80
≥10.30
80×10
0.10
0.30
<2
Henkel Loctite Europe
+49.89.9268.0
72h
200
LMS
LMS
-6
Heat Aging
Aged at temperature indicated and tested @ 22 °C
Chemical/Solvent Resistance
Aged under conditions indicated and tested @ 22 °C.
GENERAL INFORMATION
This product is not recommended for use in pure oxygen
and/or oxygen rich systems and should not be selected as
a sealant for chlorine or other strong oxidizing materials.
For safe handling information on this product, consult the
Material Safety Data Sheet (MSDS).
Where aqueous washing systems are used to clean the
surfaces before bonding, it is important to check for
compatibility of the washing solution with the adhesive. In
some cases these aqueous washes can affect the cure and
performance of the adhesive.
This product is not normally recommended for use on plastics
(particularly thermoplastic materials where stress cracking of
the plastic could result). Users are recommended to confirm
compatibility of the product with such substrates.
Directions for use
For Assembly
Environment
Motor Oil
Unleaded Gasoline
Brake fluid
Water Glycol 50/50
Ethanol
Acetone
1. For best results, clean all surfaces (external and internal)
2. If the material is an inactive metal or the cure speed is to
3. Shake the product thoroughly before use.
4. For Slip Fitted Assemblies, apply adhesive around the
5. For Press Fitted Assemblies, apply adhesive thoroughly
6. For Shrink Fitted Assemblies the adhesive should be
with a Loctite cleaning solvent and allow to dry.
slow, spray with Activator 7471 or 7649 and allow to dry.
leading edge of the pin and the inside of the collar and
use a rotating motion during assembly to ensure good
coverage.
to both bond surfaces and assemble at high press on
rates.
coated onto the pin, the collar should then be heated to
create
200
150
100
50
0
0
sufficient
100
125
°C
22
22
87
22
22
clearance
500
TDS LOCTITE
100 hr
100
100
100
100
100
100
% of initial strength
Henkel Loctite Asia Pacific
1000
for
500 hr
100
100
100
100
100
85
®
free
+81.45.758.1810
609, June-2004
3000
assembly.
1000 hr
100
100
100
100
80
85
5000