49945 Loctite, 49945 Datasheet - Page 2

• Manufacturer Part Number: 49945
• Description: ETHYL CYANOACRYLATE ADH, TUBE, 20G
• Manufacturer: Loctite
• Series: 499r

Specifications of 49945

• Adhesive Type: Ethyl Cyanoacrylate
• Color: Clear
• Dispensing Method: Tube
• Weight: 20g
• Pack Quantity: 1
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

TYPICAL ENVIRONMENTAL RESISTANCE
Hot Strength
Tested at temperature
Heat Aging
Aged at temperature indicated and tested @ 22 °C
Henkel Americas
+860.571.5100
Cured for 24 hours @ 22 °C, followed by 24 hours @ 121 °C, tested
@ 22 °C
Cured for 30 seconds @ 22 °C
After 1 week @ 22 °C
Tensile Strength, ISO 6922:
"T" Peel Strength, ISO 11339:
Lap Shear Strength, ISO 4587:
Tensile Strength, ISO 6922:
Lap Shear Strength, ISO 4587:
Steel (grit blasted)
Buna-N
Steel (degreased)
Steel (grit blasted)
Buna-N
Mild steel (grit blasted)
100
100
75
50
25
75
50
25
0
0
For the most direct access to local sales and technical support visit: www.henkel.com/industrial
0
0
1000
10
2000
40
N/mm² 12 to 25
(psi)
N/mm² 5 to 15
(psi)
N/mm
(lb/in)
N/mm² ≥9.0
(psi)
N/mm² ≥3.0
(psi)
3000
65
(1,740 to 3,625)
(725 to 2,175)
(<2.8)
(≥1,305)
(≥435)
<0.5
4000
90
LMS
120 °C
60 °C
+49.89.320800.1800
5000
Henkel Europe
120
Chemical/Solvent Resistance
Aged under conditions indicated and tested @ 22 °C.
GENERAL INFORMATION
This product is not recommended for use in pure oxygen
and/or oxygen rich systems and should not be selected as
a sealant for chlorine or other strong oxidizing materials
For safe handling information on this product, consult the
Material Safety Data Sheet (MSDS).
Directions for use:
Loctite Material Specification
LMS dated April-01, 2004. Test reports for each batch are
available for the indicated properties. LMS test reports include
selected QC test parameters considered appropriate to
specifications for customer use. Additionally, comprehensive
controls are in place to assure product quality and
consistency. Special customer specification requirements may
be coordinated through Henkel Quality.
Storage
Store product in the unopened container in a dry location.
Storage information may be indicated on the product container
labeling.
Optimal Storage: 2 °C to 8 °C. Storage below 2 °C or
greater than 8 °C can adversely affect product properties.
Material removed from containers may be contaminated during
use. Do not return product to the original container. Henkel
Corporation cannot assume responsibility for product which
has been contaminated or stored under conditions other than
those previously indicated. If additional information is required,
please contact your local Technical Service Center or
Customer Service Representative.
Conversions
(°C x 1.8) + 32 = °F
kV/mm x 25.4 = V/mil
mm / 25.4 = inches
µm / 25.4 = mil
N x 0.225 = lb
N/mm x 5.71 = lb/in
N/mm² x 145 = psi
MPa x 145 = psi
N·m x 8.851 = lb·in
N·m x 0.738 = lb·ft
N·mm x 0.142 = oz·in
mPa·s = cP
Environment
Motor oil (MIL-L-46152)
Gasoline
Isopropanol
Ethanol
Freon TA
Heat/humidity 95% RH
1. For best performance bond surfaces should be clean and
2. This product performs best in thin bond gaps (0.05 mm).
3. Excess adhesive can be dissolved with Loctite cleanup
free from grease.
solvents, nitromethane or acetone.
°C
40
22
22
22
22
40
TDS LOCTITE
LMS
100 h
100
100
100
100
100
100
% of initial strength
500 h
Henkel Asia Pacific
®
100
100
100
100
100
100
+86.21.2891.8863
499™, July-2008
1000 h
100
100
100
100
95
95