PRODUCT DESCRIPTION
LOCTITE
characteristics:
LOCTITE
increased flexibility and peel strength along with enhanced
resistance to shock.
TYPICAL PROPERTIES OF UNCURED MATERIAL
TYPICAL CURING PERFORMANCE
Under normal conditions, the atmospheric moisture initiates the
curing process. Although full functional strength is developed
in a relatively short time, curing continues for at least 24 hours
before full chemical/solvent resistance is developed.
Cure Speed vs. Substrate
Cure Speed vs. Bond Gap
The rate of cure will depend on the bondline gap. Thin bond
lines result in high cure speeds, increasing the bond gap will
decrease the rate of cure.
Cure Speed vs. Activator
Where cure speed is unacceptably long due to large gaps,
applying activator to the surface will improve cure speed.
However, this can reduce ultimate strength of the bond and
therefore testing is recommended to confirm effect.
Technology
Chemical Type
Appearance (uncured)
Components
Viscosity
Cure
Application
Key Substrates
The rate of cure will depend on the substrate used. The table
below shows the fixture time achieved on different materials
at 22 °C / 50 % relative humidity. This is defined as the time to
develop a shear strength of 0.1 N/mm².
Specific Gravity @ 25 °C
Viscosity, Brookfield - RVT, 25 °C, mPa·s (cP):
Flash Point - See MSDS
Fixture Time, seconds:
Spindle 3, speed 20 rpm
Steel (degreased)
Aluminum
Neoprene
Rubber, nitrile
ABS
PVC
Polycarbonate
Phenolic
®
®
410™ is a rubber toughened adhesive with
410™
provides
Cyanoacrylate
Ethyl cyanoacrylate
Black liquid
One part - requires no mixing
High
Humidity
Bonding
Metals, Plastics and Rubbers
the
LMS
following
1,700 to 5,000
1.1
60 to 120
10 to 30
15 to 25
15 to 25
20 to 50
50 to 100
30 to 90
20 to 60
product
LMS
TYPICAL PROPERTIES OF CURED MATERIAL
TYPICAL PERFORMANCE OF CURED MATERIAL
After 24 hours @ 22 °C
Adhesive Properties
After 24 hours @ 22 °C
After 48 hours @ 22 °C
Physical Properties:
Electrical Properties:
Lap Shear Strength, ISO 4587:
Tensile Strength, ISO 6922:
Lap Shear Strength, ISO 4587:
Coefficient of Thermal Expansion,
Coefficient of Thermal Conductivity, ISO 8302
,
W/(m·K)
Glass Transition Temperature, ASTM E 228,
°C
Dielectric Constant / Dissipation Factor, IEC 60250:
Volume Resistivity, IEC 60093, Ω·cm
Dielectric Breakdown Strength,
IEC 60243-1, kV/mm
Steel (grit blasted)
Aluminum (etched)
ABS
PVC
Polycarbonate
Phenolic
Neoprene
Nitrile
Steel (grit blasted)
Steel (grit blasted)
ISO 11359-2, K
0.05-kHz
1-kHz
1,000-kHz
LOCTITE
-1
N/mm² 22
(psi)
N/mm² 15
(psi)
N/mm² >6
(psi)
N/mm² >6
(psi)
N/mm² >5
(psi)
N/mm² 10
(psi)
N/mm² >10
(psi)
N/mm² >10
(psi)
N/mm² 18.5
(psi)
N/mm² ≥15.8
(psi)
Technical Data Sheet
®
(3,190)
(2,175)
(>870)
(>870)
(>725)
(1,450)
(>1,450)
(>1,450)
(2,680)
(≥2,290)
80×10
0.1
120
10×10
25
2.3 / <0.02
2.3 / <0.02
2.3 / <0.02
410™
March-2008
-6
15
