24231 Loctite, 24231 Datasheet - Page 3

• Manufacturer Part Number: 24231
• Description: ACRYLIC ADHESIVE, BOTTLE, 50ML
• Manufacturer: Loctite
• Series: 242r

Specifications of 24231

• Adhesive Type: Acrylic
• Color: Blue
• Dispensing Method: Bottle
• Volume: 50ml
• Pack Quantity: 1
• Mil Spec: MIL-S-46163A For Existing Designs, ASTM D-5363, NSF/ANSI 61, NSF P1, ABS, CFIA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

This product is not normally recommended for use on plastics
(particularly thermoplastic materials where stress cracking of
the plastic could result). Users are recommended to confirm
compatibility of the product with such substrates.
Directions for use:
For Assembly
For Disassembly
For Cleanup
Loctite Material Specification
LMS dated October-16, 1995 (*October 7, 1999). Test reports
for each batch are available for the indicated properties. LMS
test reports include selected QC test parameters considered
appropriate to specifications for customer use. Additionally,
comprehensive controls are in place to assure product quality
and consistency. Special customer specification requirements
may be coordinated through Henkel Quality.
Storage
Store product in the unopened container in a dry location.
Storage information may be indicated on the product container
labeling.
Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or
greater than 28 °C can adversely affect product properties.
Material removed from containers may be contaminated during
use. Do not return product to the original container. Henkel
Corporation cannot assume responsibility for product which
has been contaminated or stored under conditions other than
those previously indicated. If additional information is required,
please contact your local Technical Service Center or
Customer Service Representative.
Henkel Americas
+860.571.5100
1. For best results, clean all surfaces (external and internal)
2. If the material is an inactive metal or the cure speed is too
3. Shake the product thoroughly before use.
4. To prevent the product from clogging in the nozzle, do not
5. For Thru Holes, apply several drops of the product onto
6. For Blind Holes, apply several drops of the product down
7. For Sealing Applications, apply a 360° bead of product
8. Assemble and tighten as required.
1. Remove with standard hand tools.
2. In rare instances where hand tools do not work because
1. Cured product can be removed with a combination of
with a LOCTITE
slow, spray all threads with Activator 7471™ or 7649™
allow the tip to touch metal surfaces during application.
the bolt at the nut engagement area.
the internal threads to the bottom of the hole.
to the leading threads of the male fitting, leaving the first
thread free. Force the material into the threads to
thouroughly fill the voids. For bigger threads and voids,
adjust product amount accordingly and apply a 360° bead
of product on the female threads also.
of excessive engagement length, apply localized heat to
nut or bolt to approximately 250 °C. Disassemble while
hot.
soaking in a Loctite solvent and mechanical abrasion
such as a wire brush.
and allow to dry.
For the most direct access to local sales and technical support visit: www.henkel.com/industrial
®
cleaning solvent and allow to dry.
LMS
+49.89.320800.1800
Henkel Europe
Conversions
(°C x 1.8) + 32 = °F
kV/mm x 25.4 = V/mil
mm / 25.4 = inches
µm / 25.4 = mil
N x 0.225 = lb
N/mm x 5.71 = lb/in
N/mm² x 145 = psi
MPa x 145 = psi
N·m x 8.851 = lb·in
N·m x 0.738 = lb·ft
N·mm x 0.142 = oz·in
mPa·s = cP
Note
The data contained herein are furnished for information only
and are believed to be reliable.
responsibility for the results obtained by others over whose
methods we have no control. It is the user's responsibility to
determine suitability for the user's purpose of any production
methods mentioned herein and to adopt such precautions as
may be advisable for the protection of property and of persons
against any hazards that may be involved in the handling and
use thereof. In light of the foregoing, Henkel Corporation
specifically disclaims all warranties expressed or implied,
including warranties of merchantability or fitness for a
particular purpose, arising from sale or use of Henkel
Corporation’s products. Henkel Corporation specifically
disclaims any liability for consequential or incidental
damages of any kind, including lost profits. The discussion
herein of various processes or compositions is not to be
interpreted as representation that they are free from
domination of patents owned by others or as a license under
any Henkel Corporation patents that may cover such
processes or compositions.
prospective user test his proposed application before repetitive
use, using this data as a guide. This product may be covered
by one or more United States or foreign patents or patent
applications.
Trademark usage
Except as otherwise noted, all trademarks in this document
are trademarks of Henkel Corporation in the U.S. and
elsewhere.
Patent and Trademark Office.
Reference 1.4
®
denotes a trademark registered in the U.S.
TDS LOCTITE
We recommend that each
®
242
We cannot assume
Henkel Asia Pacific
®
+86.21.2891.8863
, December-2009