CDB8952 Cirrus Logic Inc, CDB8952 Datasheet - Page 3
![no-image](/images/manufacturer_photos/0/1/141/cirrus_logic_inc_sml.jpg)
CDB8952
Manufacturer Part Number
CDB8952
Description
Development Kit
Manufacturer
Cirrus Logic Inc
Datasheet
1.CDB8952T.pdf
(12 pages)
Specifications of CDB8952
Silicon Manufacturer
Cirrus Logic
Application Sub Type
10Base-T & 100Base-X Transceiver
Kit Application Type
Communication & Networking
Silicon Core Number
CS8952
Kit Contents
Evaluation Board
Rohs Compliant
No
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
DS206DB2
NOTE: Physical address 00000 is a special broadcast
HDR1 - MII Drive Select. When this header is left
open, the CS8952 MII drivers will conform to the
IEEE 802.3u specification. When a shorting cap is
installed, the CS8952 MII drivers will be reduced
to 4mA.
The CS8952 checks the status of HDR1 only dur-
ing power-on or reset. A reset or power cycle is re-
quired before any changes in this jumper setting
will take effect.
HDR4, HDR5 - Auto-Negotiation Select 0 and 1.
These headers are used to select the forced or ad-
vertised auto-negotiation modes as indicated in Ta-
ble 4.
The CS8952 checks the status of HDR4 and HDR5
only during power-on or reset. A reset or power cy-
CDB8952
Crystal LAN™ 10Base-T and 100Base-X Transceiver
pins 2-3
pins 1-2
pins 2-3
pins 2-3
pins 1-2
pins 1-2
shorted
shorted
shorted
shorted
shorted
shorted
HDR5
(AN1)
open
open
open
address. All devices will respond to this address
in addition to the one selected using S3. Setting
S3 to 00000 will cause the CS8952 to set the
ISOLATE bit in the Basic Mode Control Regis-
ter, isolating itself from all MII signals except
MDC and MDIO. It will remain isolated until this
bit is cleared.
Care should be taken when reading from phys-
ical address 00000 when multiple devices
reside on the same MII.
Table 4. Auto-Negotiation Select
pins 2-3
pins 1-2
pins 2-3
pins 1-2
pins 2-3
pins 1-2
shorted
shorted
shorted
shorted
shorted
shorted
HDR4
(AN0)
open
open
open
Speed
100/10
100
100
100
100
10
10
10
10
CIRRUS LOGIC ADVANCED PRODUCT DATABOOK
Forced/
Forced
Forced
Forced
Forced
Auto
Auto
Auto
Auto
Auto
Auto
f Duplex
Full/Half
Full/Hal
Half
Half
Half
Half
Full
Full
Full
Full
cle is required before any changes in these jumper
settings will take effect.
HDR6, HDR7 - Transmit Slew Rate Select 0 and 1.
These headers are used to select the rise and fall
times of the 100BASE-TX transmitter output
waveform as indicated in Table 5.
HDR15 - Table 6 describes the effect of shorting
the listed pin pairs.
HDR34 - Test 0. This header is for factory test pur-
poses only, and should be left open for normal op-
eration.
HDR35 - Test 1. This header is for factory test pur-
poses only, and should be left open for normal op-
eration.
HDR42 - TX_CLK Source Select. This header, in
conjunction with HDR43, is used to select the
TX_CLK source. When pins 1 and 2 are selected,
TX_CLK is supplied from the CS8952 CLK25 out-
put. When pins 2 and 3 are shorted, TX_CLK is
supplied externally from J1. When no shorting cap
is installed, HDR43 must be configured so that
TX_CLK is an output from the CS8952.
NOTE: No shorting cap should be installed on this
HDR43 - TX_CLK Mode Select. (Table 7)
The CS8952 checks the status of HDR43 only dur-
ing power-on or reset. A reset or power cycle is re-
quired before any changes in this jumper setting
will take effect.
pins 2-3 shorted
pins 1-2 shorted
pins 2-3 shorted
pins 1-2 shorted
pins 2-3 shorted
pins 1-2 shorted
(TXSLEW1)
HDR7
open
open
open
header when TX_CLK is configured as an out-
put (see HDR43).
Table 5. Transmit Slew Rate
pins 2-3 shorted
pins 2-3 shorted
pins 2-3 shorted
pins 1-2 shorted
pins 1-2 shorted
pins 1-2 shorted
(TXSLEW0)
HDR6
open
open
open
Rise/Fall
0.5 ns
1.0 ns
1.5 ns
2.0 ns
2.5 ns
3.0 ns
3.5 ns
4.0 ns
4.5 ns
Time
3