AD9269-40EBZ Analog Devices Inc, AD9269-40EBZ Datasheet - Page 8
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
AD9269-40EBZ
Manufacturer Part Number
AD9269-40EBZ
Description
A/D Converter Eval. Board
Manufacturer
Analog Devices Inc
Specifications of AD9269-40EBZ
Silicon Manufacturer
Analog Devices
Application Sub Type
ADC
Kit Application Type
Data Converter
Silicon Core Number
AD9269
Kit Contents
Software, Evaluation Board
Number Of Adc's
2
Number Of Bits
16
Sampling Rate (per Second)
40M
Data Interface
Serial, SPI™
Inputs Per Adc
1 Differential
Input Range
2 Vpp
Power (typ) @ Conditions
136.3mW @ 40MSPS
Voltage Supply Source
Analog and Digital
Operating Temperature
-40°C ~ 85°C
Utilized Ic / Part
AD9269
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
UG-003
EVALUATION BOARD SOFTWARE QUICK START PROCEDURES
This section provides quick start procedures for using the AD9650,
AD9268, AD9258, AD9251, AD9231, AD9204, AD9269, and
AD6659
settings are described.
CONFIGURING THE BOARD
Before using the software for testing, configure the evaluation
board as follows:
1.
2.
3.
4.
5.
6.
7.
USING THE SOFTWARE FOR TESTING
Setting Up the ADC Data Capture
After configuring the board, set up the ADC data capture using
the following steps:
1.
Connect the evaluation board to the data capture board,
as shown in Figure 1 and Figure 2.
Connect one 6 V, 2.5 A switching power supply (such as
the CUI, Inc., EPS060250UH-PHP-SZ supplied) to the
AD9650, AD9268, AD9258, AD9251, AD9231, AD9204,
AD9269, or AD6659 board.
Connect one 6 V, 2.5 A switching power supply (such
as the CUI EPS060250UH-PHP-SZ supplied) to the
HSC-ADC-EVALCZ board.
Connect the HSC-ADC-EVALCZ board (J6) to the PC
with a USB cable.
On the ADC evaluation board, confirm that three jumpers are
installed on J302, one between Pin 1and Pin 2, one between
Pin 4 and Pin 5, and one between Pin 8 and Pin 9, to connect
the SPI bus to the DUT.
If using an AD9269 family board, ensure that J605 (OSC_EN)
has a jumper installed to use the on-board 50 MHz/65 MHz/
80 MHz Valpey Fisher VFAC3 oscillator. If using an AD9650
or AD9268 family board, make sure a low jitter sample
clock is applied at J602.
On the ADC evaluation board, use a clean signal generator
with low phase noise to provide an input signal to the desired
A and/or B channel(s). Use a 1 m, shielded, RG-58, 50 Ω
coaxial cable to connect the signal generator. For best results,
use a narrow-band, band-pass filter with 50 Ω terminations
and an appropriate center frequency. (Analog Devices uses
TTE, Allen Avionics, and K&L band-pass filters.)
Open VisualAnalog on the connected PC. The appropriate
part type should be listed in the status bar of the
VisualAnalog – New Canvas window. Select the template
that corresponds to the type of testing to be performed
(see Figure 6 where the AD9268 is shown as an example).
evaluation board. Both the default and optional
Rev. A | Page 8 of 40
2.
3.
After the template is selected, a message appears asking if
the default configuration can be used to program the FPGA
(see Figure 7). Click Yes and the window closes.
To change features to settings other than the default settings,
click the Expand Display button, located on the bottom
right corner of the window, to see what is shown in Figure 9.
Detailed instructions for changing the features and capture
settings can be found in the
VisualAnalog Converter Evaluation Tool Version 1.0 User
Manual. After the changes are made to the capture settings,
click Collapse Display (see Figure 8).
Figure 8. VisualAnalog Window Toolbar, Collapsed Display
Figure 7. VisualAnalog Default Configuration Message
Figure 6. VisualAnalog, New Canvas Window
Evaluation Board User Guide
AN-905
Application Note,