8800 3M, 8800 Datasheet - Page 118

• Manufacturer Part Number: 8800
• Description: Static Dissipative Rubber Table Mat
• Manufacturer: 3M

Specifications of 8800

• Ground Terminals: Stud
• External Width: 2ft
• Thickness: 1.7mm
• Roll Length: 40ft
• Color: Gray
• Lead Free Status / RoHS Status: na

3M
“No Wax” ESD Tile
One of the key attributes of 3M ESD Vinyl Tile is its ability to be cleaned
and maintained with a minimum of cost and effort.
See 3M ESD Floor Tile 8400 Series instructions for complete
maintenance details.
Unique Cleanability
3M ESD Floor Tile 8400 Series can
be repeatedly cleaned and then
buffed to a high sheen without ever
using wax.
With some other ESD tiles, normal
cleaning procedures may dull the
finish and can even degrade the
electrical properties. Conductive
wax or glaze must then be used to
restore their shine and conductivity.
3M Tiles 8400 Series maintain
their electrical properties and
can be shined like new with
simple buffing. The photos below
demonstrate this feature.
The floor section shown is a test
patch of 3M
8412 installed in a high-traffic area
of a regional telephone company
warehouse. To determine whether
the tile could truly withstand
serious abuse and then be returned
to like-new condition with simple
cleaning and without wax, the
section was intentionally left
unattended for 11 months as it was
subjected to the wear and grime of
continual forklift traffic. The result
of this abuse is evident in Photo 1.
After being swept, the tile was
scrubbed with neutral cleaner, left
to dry, and then buffed according to
the maintenance procedure established. As Photos 2 and 3 show, in
spite of nearly a year of dramatic abuse, the high gloss of the restored
floor finish is similar to that of the tile when it is newly installed—
without the use of any kind of wax.
This trial is an impressive demonstration of the durability of the 3M ESD
tile and its unique “no wax” feature.
™
Static Control Vinyl Floor Tile
™
Static Dissipative Tile
Permanent Flooring Products
1
2
3
3M
24.5 in. x 24.5 in. (622 mm x 622 mm) size used for raised
access floor panels.
Mechanical Properties
Static Dissipative Floor Tile (Model numbers 8411–8427)
Conductive Floor Tile (Model numbers 8431–8447)
Flammability
Critical Radiant Flux
Physical Specifications
Hardness (ASTM D 2240)
Flexibility (CSA 126.2)
Abrasion Resistance
Static Load (ASTM F970)
125 lbs, 0.25 in. diameter
indentor foot, 24 hours
Residual indentation
700 lbs., 1.125 in. diameter
indentor foot, 2 hours
Residual indentation
Electrical Properties (typical)
Static Dissipative
Electrical Resistance
Static Generation
Static Decay
Sizes
Static Dissipative and Conductive
0.125 H x 12 W x 12 in. L (3.2 x 305 x 305 mm)
0.125 H x 24.25 W x 24.25 in. L (3.2 x 622 x 622 mm)
-for raised access floor panels
0.125 H x 24.25 W x 24.25 in. L (3.2 x 622 x 622 mm)
0.125 H x 36 W x 36 in. L (3.2 x 915 x 915 mm)
-for seamwelded installations
(With conductive footwear at 20% RH)
Flame Spread Index
(ASTM E162/ASTM E84)
Smoke Development
(ASTM E84)
(ASTM E648/NFPA 253)
100 mm mandrel @ 25˚ C
(ASTM D 3389)
Taber H22 wheel, 70 rpm
(Surface-to-ground, ESD S7.1)
1 x 10
<50 volts
(Federal TM 101C, Method 4046 @ 15% RH [5000 volts to 0 volts])
<0.10 sec.
™
ESD Floor Tile 8400 Series is available in the special
6
to 1 x 10
9
ohm
Meets Class 1 requirements
Meets Class 1 requirements
>1.1 w/cm2
Meets ASTM F1066-99
Meets US Federal Specification
SS-T-312B
55 ± 5 Shore D
Does not break
0.445 grams
(weight of tile removed per 1000 cycles)
2500 PSI point load
3% of tile thickness
700 PSI point load
1% of tile thickness
Conductive
2.5 x 10
<25 volts
<0.03 sec.
4
to 1 x 10
6
ohm
113